AT49BV002A-70TI Atmel, AT49BV002A-70TI Datasheet
AT49BV002A-70TI
Specifications of AT49BV002A-70TI
Related parts for AT49BV002A-70TI
AT49BV002A-70TI Summary of contents
Page 1
... When the device is deselected, the CMOS standby current is less than 50 µA. For the AT49BV002AN(T) pin 1 for PLCC package and pin 9 for the TSOP package are AT49BV002A(N)(T) does not require high input voltages for programming. Five-volt- only commands determine the read and programming operation of the device. Read- ing data out of the device is similar to reading from an EPROM ...
Page 2
... Function Addresses Chip Enable Output Enable Write Enable RESET Data Inputs/Outputs I/O0 13 A11 A13 4 A14 5 A17 VCC 8 *RESET 9 A16 10 A15 11 A12 *This pin the AT49BV002AN(T). 29 A14 28 A13 A11 A10 I/ A10 I/O7 28 I/O6 27 I/O5 26 I/O4 I/ GND 23 I/O2 22 I/ 3353G–FLASH–8/05 ...
Page 3
... Read The AT49BV002A(N)(T) is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the out- puts. The outputs are put in the high impedance state whenever high. This dual-line control gives designers flexibility in preventing bus contention ...
Page 4
... RESET pin, the boot block array can be reprogrammed even if the boot block lockout feature has been enabled (see page 5). The RESET feature is not available on the AT49BV002AN(T). 4.4 Erasure Before a byte can be reprogrammed, the main memory blocks or parameter blocks which con- tains the byte must be erased. The erased state of the memory bits is a logical “ ...
Page 5
... This feature does not have to be activated; the boot block’s usage as a write protected region is optional to the user. The address range of the boot block is 00000 to 03FFF for the AT49BV002A(N) while the address range of the boot block is 3C000 to 3FFFF for the AT49BV002A(N)T. ...
Page 6
... DATA Polling The AT49BV002A(N)(T) features DATA polling to indicate the end of a program cycle. During a program cycle an attempted read of the last byte loaded will result in the complement of the loaded data on I/O7. Once the program cycle has been completed, true data is valid on all out- puts and the next cycle may begin ...
Page 7
... A11 - A0 (Hex); A11 - A17 (don’t care). 2. Since A11 is don’t care, AAA can be replaced with 2AA. 3. The 16K byte boot sector has the address range 00000H to 03FFFH for the AT49BV002A(N) and 3C000H to 3FFFFH for the AT49BV002A(N)T 4. Either one of the Product ID Exit commands can be used. ...
Page 8
... Software Notes can Refer to AC Programming Waveforms. = 12.0V ± 0.5V Manufacturer Code: 1FH, Device Code: 07H - AT49BV002A(N), 08H - AT49BV002A(N)T 5. See details under “Software Product Identification 6. This pin is not available on the AT49BV002AN(T Characteristics Symbol Parameter I Input Load Current LI I Output Leakage Current ...
Page 9
... This parameter is characterized and is not 100% tested. 3353G–FLASH–8/05 (1)(2)(3)(4) ADDRESS VALID ACC HIGH after the address transition without impact on t ACC after the falling edge of CE without impact AT49BV002A(N)(T) AT49BV002A(N)(T)-70 Min Max OUTPUT VALID . ACC after an address change CE ACC ...
Page 10
... Input Test Waveform and Measurement Level DRIVING LEVELS < 13. Output Load Test 14. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. This parameter is characterized and is not 100% tested. AT49BV002A(N)(T) 10 2.4V AC 1.5V 0.4V 3.0V 1.8K OUTPUT PIN 30 pF 1.3K Max MEASUREMENT LEVEL Units Conditions pF V ...
Page 11
... Write Pulse Width ( Data Set-up Time Data, OE Hold Time DH OEH t Write Pulse Width High WPH 16. AC Byte Load Waveforms 16.1 WE Controlled OE ADDRESS CE WE DATA IN 16.2 CE Controlled OE ADDRESS WE CE DATA IN 3353G–FLASH–8/05 t OES t OEH OES t OEH AT49BV002A(N)(T) Min Max Units WPH WPH ...
Page 12
... For chip erase, the address should be 555. For sector erase, the address depends on what sector erased. (See note 4 under “Command Definition Table” on page 3. For chip erase, the data should be 10H, and for sector erase, the data should be 30H. AT49BV002A(N)(T) 12 Min 0 ...
Page 13
... OEHP 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. 3353G–FLASH–8/05 Min OEH t OE HIGH Min (1)(2)( OEH OEHP HIGH Z AT49BV002A(N)(T) Typ Max Units Typ Max Units ...
Page 14
... Additional Device Code is read for address 0003H 3. The device does not remain in identification mode if powered down. 4. The device returns to standard operation mode. 5. Manufacturer Code:1FH Device Code: 07H - AT49BV002A(N) 08H - AT49BV002A(N)T Additional Device Code: 0FH - AT49BV002A(N)(T) AT49BV002A(N)(T) 14 26. Boot Block Lockout Feature Enable Algorithm LOAD DATA F0 TO ...
Page 15
... Plastic, J-Leaded Chip Carrier Package (PLCC) 32T 32-Lead, Thin Small Outline Package (TSOP) 32V 32-Lead, Thin Small Outline Package (VSOP mm) 3353G–FLASH–8/05 Ordering Code Package AT49BV002A-70JI 32J AT49BV002A-70TI 32T AT49BV002A-70VI 32V AT49BV002AN-70JI 32J AT49BV002AN-70TI 32T AT49BV002AN-70VI 32V AT49BV002AT-70JI ...
Page 16
... Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010 (0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004 (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT49BV002A(N)(T) 16 1.14(0.045 PIN NO. 1 IDENTIFIER ...
Page 17
... Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R 3353G–FLASH–8/05 PIN SEATING PLANE A1 TITLE 32T, 32-lead ( Package) Plastic Thin Small Outline Package, Type I (TSOP) AT49BV002A(N)(T) 0º ~ 8º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – ...
Page 18
... E Notes: 1. This package conforms to JEDEC reference MO-142, Variation BA. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT49BV002A(N)(T) 18 PIN SEATING PLANE A1 TITLE ...
Page 19
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...