AT93C56W-10SC Atmel, AT93C56W-10SC Datasheet
AT93C56W-10SC
Specifications of AT93C56W-10SC
Related parts for AT93C56W-10SC
AT93C56W-10SC Summary of contents
Page 1
... PDIP, 8-lead JEDEC and EIAJ SOIC, and 8-lead TSSOP Packages Description The AT93C46/56/57/66 provides 1024/2048/4096 bits of serial electrically erasable programmable read only memory (EEPROM) organized as 64/128/256 words of 16 bits each, when the ORG pin is connected to V each when it is tied to ground. The device is optimized for use in many industrial and commercial applications where low power and low voltage operations are essential ...
Page 2
The AT93C46/56/57/66 is enabled through the Chip Select pin (CS), and accessed via a 3-wire serial interface consist- ing of Data Input (DI), Data Output (DO), and Shift Clock (SK). Upon receiving a READ instruction at DI, the address is ...
Page 3
Pin Capacitance Applicable over recommended operating range from T Symbol Test Conditions C Output Capacitance (DO) OUT C Input Capacitance (CS, SK, DI) IN Note: 1. This parameter is characterized and is not 100% tested. DC Characteristics Applicable over ...
Page 4
AC Characteristics Applicable over recommended operating range from TTL Gate and 100 pF (unless otherwise noted). Symbol Parameter SK Clock f SK Frequency t SK High Time SKH t SK Low Time SKL Minimum CS t ...
Page 5
... 10XXXXX 01XXXXX 00XXXXX AT93C46/56/57/66 Data x 16 Comments Reads data stored in memory, at specified address. Write enable must precede all programming modes. Erase memory location Writes memory location Erases all memory locations. Valid only 4.5V to 5.5V Writes all memory locations. Valid 15 0 only ...
Page 6
... DI. The DO pin outputs the READY/BUSY status of the part brought high after being kept low for a minimum of 250 still in progress. A logic “1” indicates that the memory location at the specified address has been written with the data pattern contained in the instruction and the part is ready for further instructions ...
Page 7
Timing Diagrams Synchronous Data Timing Note: 1. This is the minimum SK period. Organization Key for Timing Diagrams AT93C46 (1K) I Note ...
Page 8
EWEN Timing EWDS Timing WRITE Timing HIGH IMPEDANCE DO (1) WRAL Timing HIGH IMPEDANCE DO Note: 1. Valid only 4.5V to 5.5V. CC AT93C46/56/57/66 8 ...
Page 9
ERASE Timing HIGH IMPEDANCE DO (1) TERAL Timing HIGH IMPEDANCE DO Note: 1. Valid only 4.5V to 5.5V ... N-1 N-2 ...
Page 10
AT93C46 Ordering Information t (max) I (max) I (max (ms) (µA) (µA) 10 2000 30.0 30.0 10 800 10.0 10.0 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small ...
Page 11
AT93C46 Ordering Information (Continued) t (max) I (max) I (max (ms) (µA) (µA) 10 600 10.0 10 0.1 0.1 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing ...
Page 12
... AT93C56-10SC AT93C56W-10SC 2000 AT93C56-10PI AT93C56-10SI AT93C56W-10SI 1000 AT93C56-10PC-2.7 AT93C56-10SC-2.7 AT93C56W-10SC-2.7 1000 AT93C56-10PI-2.7 AT93C56-10SI-2.7 AT93C56W-10SI-2.7 500 AT93C56-10PC-2.5 AT93C56-10SC-2.5 AT93C56W-10SC-2.5 500 AT93C56-10PI-2.5 AT93C56-10SI-2.5 AT93C56W-10SI-2.5 Package Type Options Package Operation Range 8P3 Commercial 8S1 (0°C to 70°C) 8S2 8P3 Industrial 8S1 (-40°C to 85°C) ...
Page 13
AT93C57 Ordering Information t (max) I (max) I (max (ms) (µA) (µA) 10 2000 30.0 30.0 10 800 10.0 10.0 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small ...
Page 14
AT93C66 Ordering Information t (max) I (max) I (max (ms) (µA) (µA) 10 2000 30.0 30.0 10 800 10.0 10.0 10 600 10.0 10.0 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, ...
Page 15
Packaging Information 8P3, 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-001 BA .400 (10.16) .355 (9.02) PIN 1 .300 (7.62) REF .210 (5.33) MAX .100 (2.54) BSC SEATING PLANE .150 (3.81) .115 ...
Page 16
... No licenses to patents or other intellectual prop- erty of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life suppor t devices or systems. ...