AT49F040-12JI Atmel, AT49F040-12JI Datasheet - Page 2
![IC FLASH 4MBIT 120NS 32PLCC](/photos/7/21/72190/453-32-plcc_sml.jpg)
AT49F040-12JI
Manufacturer Part Number
AT49F040-12JI
Description
IC FLASH 4MBIT 120NS 32PLCC
Manufacturer
Atmel
Datasheet
1.AT49F040-70VI.pdf
(13 pages)
Specifications of AT49F040-12JI
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
4M (512K x 8)
Speed
120ns
Interface
Parallel
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
32-PLCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
AT49F04012JI
To allow for simple in-system reprogrammability, the
AT49F040 does not require high input voltages for pro-
gramming. Five-volt-only commands determine the read
and programming operation of the device. Reading data
out of the device is similar to reading from an EPROM.
Reprogramming the AT49F040 is performed by erasing the
entire 4 megabits of memory and then programming on a
byte-by-byte basis. The byte programming time is a fast
50 µs. The end of a program cycle can be optionally
detected by the DATA polling feature. Once the end of a
Block Diagram
Device Operation
READ: The AT49F040 is accessed like an EPROM. When
CE and OE are low and WE is high, the data stored at the
memory location determined by the address pins is
asserted on the outputs. The outputs are put in the
high impedance state whenever CE or OE is high. This
dual-line control gives designers flexibility in preventing bus
contention.
ERASURE: Before a byte can be reprogrammed, the 512K
bytes memory array (or 496K bytes if the boot block fea-
tured is used) must be erased. The erased state of the
memory bits is a logical “1”. The entire device can be
erased at one time by using a 6-byte software code. The
software chip erase code consists of 6-byte load com-
mands to specific address locations with a specific data
pattern (please refer to the Chip Erase Cycle Waveforms).
After the software chip erase has been initiated, the device
will internally time the erase operation so that no external
clocks are required. The maximum time needed to erase
the whole chip is t
been enabled, the data in the boot sector will not be
erased.
BYTE PROGRAMMING: Once the memory array is
erased, the device is programmed (to a logical “0”) on a
byte-by-byte basis. Please note that a data “0” cannot be
2
EC
. If the boot block lockout feature has
ADDRESS
INPUTS
AT49F040
GND
VCC
WE
OE
CE
OE, CE, AND WE
Y DECODER
X DECODER
LOGIC
byte program cycle has been detected, a new access for a
read or program can begin. The typical number of program
and erase cycles is in excess of 10,000 cycles.
The optional 16K bytes boot block section includes a repro-
gramming write lock out feature to provide data integrity.
The boot sector is designed to contain user secure code,
and when the feature is enabled, the boot sector is perma-
nently protected from being reprogrammed.
programmed back to a “1”; only erase operations can con-
vert “0”s to “1”s. Programming is accomplished via the
internal device command register and is a 4 bus cycle
operation (please refer to the Command Definitions table).
The device will automatically generate the required internal
program pulses.
The program cycle has addresses latched on the falling
edge of WE or CE, whichever occurs last, and the data
latched on the rising edge of WE or CE, whichever occurs
first. Programming is completed after the specified t
time. The DATA polling feature may also be used to indi-
cate the end of a program cycle.
BOOT BLOCK PROGRAMMING LOCKOUT: The device
has one designated block that has a programming lockout
feature. This feature prevents programming of data in the
designated block once the feature has been enabled. The
size of the block is 16K bytes. This block, referred to as the
boot block, can contain secure code that is used to bring up
the system. Enabling the lockout feature will allow the boot
code to stay in the device while data in the rest of the
device is updated. This feature does not have to be acti-
vated; the boot block’s usage as a write protected region is
optional to the user. The address range of the boot block is
00000H to 03FFFH.
DATA INPUTS/OUTPUTS
BLOCK (16K BYTES)
OPTIONAL BOOT
INPUT/OUTPUT
MAIN MEMORY
(496K BYTES)
DATA LATCH
Y-GATING
I/O7 - I/O0
BUFFERS
8
7FFFFH
04000H
03FFFH
00000H
BP
cycle