AT29C020-15JC Atmel, AT29C020-15JC Datasheet - Page 4
![IC FLASH 2MBIT 150NS 32PLCC](/photos/7/21/72190/453-32-plcc_sml.jpg)
AT29C020-15JC
Manufacturer Part Number
AT29C020-15JC
Description
IC FLASH 2MBIT 150NS 32PLCC
Manufacturer
Atmel
Datasheet
1.AT29C020-12JU.pdf
(17 pages)
Specifications of AT29C020-15JC
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
2M (256K x 8)
Speed
150ns
Interface
Parallel
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Package / Case
32-PLCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
AT29C02015JC
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
4.5
4.6
4.7
4.8
4
Hardware Data Protection
Product Identification
DATA Polling
Toggle Bit
AT29C020
shipped from Atmel, the software data protection feature is disabled. To enable the software
data protection, a series of three program commands to specific addresses with specific data
must be performed. After the software data protection is enabled the same three program com-
mands must begin each program cycle in order for the programs to occur. All software program
commands must obey the sector program timing specifications. Once set, the software data pro-
tection feature remains active unless its disable command is issued. Power transitions will not
reset the software data protection feature; however, the software feature will guard against inad-
vertent program cycles during power transitions.
After setting SDP, any attempt to write to the device without the 3-byte command sequence will
start the internal write timers. No data will be written to the device; however, for the duration of
t
After the software data protection’s 3-byte command code is given, a sector of data is loaded
into the device using the sector program timing specifications.
Hardware features protect against inadvertent programs to the AT29C020 in the following ways:
(a) V
delay – once V
(typical) before programming; (c) Program inhibit – holding any one of OE low, CE high or WE
high inhibits program cycles; and (d) Noise filter – pulses of less than 15 ns (typical) on the WE
or CE inputs will not initiate a program cycle.
The product identification mode identifies the device and manufacturer as Atmel. It may be
accessed by hardware or software operation. The hardware operation mode can be used by an
external programmer to identify the correct programming algorithm for the Atmel product.
In addition, users may wish to use the software product identification mode to identify the part
(i.e. using the device code), and have the system software use the appropriate sector size for
program operations. In this manner, the user can have a common board design for 256K to
4-megabit densities and, with each density’s sector size in a memory map, have the system soft-
ware apply the appropriate sector size.
For details, see Operating Modes (for hardware operation) or Software Product Identification.
The manufacturer and device code is the same for both modes.
The AT29C020 features DATA polling to indicate the end of a program cycle. During a program
cycle an attempted read of the last byte loaded will result in the complement of the loaded data
on I/O7. Once the program cycle has been completed, true data is valid on all outputs and the
next cycle may begin. DATA polling may begin at any time during the program cycle.
In addition to DATA polling the AT29C020 provides another method for determining the end of a
program or erase cycle. During a program or erase operation, successive attempts to read data
from the device will result in I/O6 toggling between one and zero. Once the program cycle has
completed, I/O6 will stop toggling and valid data will be read. Examining the toggle bit may begin
at any time during a program cycle.
WC
, a read operation will effectively be a polling operation.
CC
sense – if V
CC
has reached the V
CC
is below 3.8V (typical), the program function is inhibited; (b) V
CC
sense level, the device will automatically time out 5 ms
0291S–FLASH–11/08
CC
power on