AT28C010E-12PI Atmel, AT28C010E-12PI Datasheet
AT28C010E-12PI
Specifications of AT28C010E-12PI
Available stocks
Related parts for AT28C010E-12PI
AT28C010E-12PI Summary of contents
Page 1
... DATA polling of I/O7. Once the end of a write cycle has been detected a new access for a read or write can begin. Atmel’s AT28C010 has additional features to ensure high quality and manufacturabil- ity. The device utilizes internal error correction for extended endurance and improved data retention characteristics ...
Page 2
Pin Configurations Pin Name Function A0 - A16 Addresses CE Chip Enable OE Output Enable WE Write Enable I/O0 - I/O7 Data Inputs/Outputs NC No Connect DC Don’t Connect 2.1 32-lead TSOP Top View A11 ...
Page 3
... Read The AT28C010 is accessed like a Static RAM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state when either high. This dual-line control gives designers flexibility in preventing bus contention in their system. ...
Page 4
... A software controlled data protection feature has been implemented on the AT28C010. When enabled, the software data protection (SDP), will prevent inadvertent writes. The SDP feature may be enabled or disabled by the user; the AT28C010 is shipped from Atmel with SDP disabled. SDP is enabled by the host system issuing a series of three write commands; three specific bytes of data are written to three specific addresses (refer to Software Data Protection Algo- rithm) ...
Page 5
DC and AC Operating Range Operating Temperature (Case) V Power Supply CC 6. Operating Modes Mode Read (2) Write Standby/Write Inhibit Write Inhibit Write Inhibit Output Disable Notes can ...
Page 6
AC Read Characteristics Symbol Parameter t Address to Output Delay ACC ( Output Delay CE ( Output Delay OE (3)( Output Float DF Output Hold from OE, CE ...
Page 7
Input Test Waveforms and Measurement Level 12. Output Test Load 13. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. This parameter is characterized and is not 100% ...
Page 8
AC Write Characteristics Symbol Parameter Address, OE Set-up Time AS OES t Address Hold Time AH t Chip Select Set-up Time CS t Chip Select Hold Time CH t Write Pulse Width (WE or CE) WP ...
Page 9
Page Mode Characteristics Symbol Parameter t Write Cycle Time WC t Address Set-up Time AS t Address Hold Time AH t Data Set-up Time DS t Data Hold Time DH t Write Pulse Width WP t Byte Load Cycle ...
Page 10
Software Data Protection (1) Enable Algorithm LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA A0 TO ADDRESS 5555 WRITES ENABLED LOAD DATA XX TO (4) ANY ADDRESS LOAD LAST BYTE TO LAST ADDRESS ...
Page 11
Data Polling Characteristics Symbol Parameter t Data Hold Time Hold Time OEH ( Output Delay OE t Write Recovery Time WR Notes: 1. These parameters are characterized and not 100% tested. 2. See ...
Page 12
Ordering Information 26.1 Standard Package I (mA ACC (ns) Active Standby 120 40 0.2 150 40 0.2 Note: 1. See “Valid Part Numbers” on page 26.2 Green Package Option (Pb/Halide-free) I (mA ACC (ns) Active ...
Page 13
... The following table lists standard Atmel products that can be ordered. Device Numbers Speed AT28C010 12 AT28C010E 12 AT28C010 15 AT28C010E 15 28. Die Products Reference Section: Parallel EEPROM Die Products 0353G–PEEPR–10/06 Package and Temperature Combinations JI, JU, PI, TI, TU, PU JI, PI, TI, JU, PU, TU JI, JU, PI, TI, TU, PU ...
Page 14
Packaging Information 29.1 32J – PLCC 1.14(0.045) X 45˚ 0.51(0.020)MAX 45˚ MAX (3X) Notes: 1. This package conforms to JEDEC reference MS-016, Variation AE. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is ...
Page 15
PDIP A SEATING PLANE Note: 1. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 ...
Page 16
TSOP Pin 1 Identifier e E Notes: 1. This package conforms to JEDEC reference MO-142, Variation BD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and ...
Page 17
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...