AT27BV256-70JI Atmel, AT27BV256-70JI Datasheet
AT27BV256-70JI
Specifications of AT27BV256-70JI
Available stocks
Related parts for AT27BV256-70JI
AT27BV256-70JI Summary of contents
Page 1
... AT27BV256 consumes less than one fifth the power of a standard CC 5V EPROM. Standby mode supply current is typically less than 1 µA at 3V. The AT27BV256 simpli- fies system design and stretches battery lifetime even further by eliminating the need for power supply regulation. ...
Page 2
... Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry-standard programming equipment to select the proper program- ming algorithms and voltages. The AT27BV256 programs exactly the same way as a standard 5V AT27C256R and uses the same programming equipment. 2. Pin Configurations ...
Page 3
... Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the (1) operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect (1) device reliability (1) AT27BV256 3 ...
Page 4
... Power Supply CC AT27BV256 ( ( A14 = V ≤ 3.6V, or 4.5V ≤ ≤ 5.5V 6.5V except A9 which is set to V and A0 which is toggled select the Device Code byte. IH AT27BV256-70 -40°C - 85°C 2.7V to 3.6V 5V ± 10% Outputs D OUT High Z High OUT D OUT High Z Identification Code 0601E–EPROM–12/07 ...
Page 5
... I (CMOS SB1 CC I (TTL 2 0.5V SB2 MHz mA OUT 2 -400 µ and removed simultaneously with or after except during programming. The supply current would then be the sum AT27BV256 Min Max ±1 ± 100 = 3.6V 8 -0.6 0.8 -0 0 0.4 ...
Page 6
... Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified may be delayed may be delayed This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. 6. When reading a AT27BV256, a 0.1 µF capacitor is required across V AT27BV256 6 Condition ...
Page 7
... Output Test Load 13. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. 0601E–EPROM–12/ < (10 Note 100 pF including jig capacitance. Max 8 12 AT27BV256 Units Conditions OUT 7 ...
Page 8
... Programming Waveforms Notes: 1. The Input Timing Reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27BV256 a 0.1 µF capacitor is required across V transients. AT27BV256 8 (1) and 2.0V for and ground to suppress spurious voltage PP 0601E–EPROM–12/07 ...
Page 9
... Program Pulse width tolerance is 100 17. Atmel’s AT27BV256 Integrated Product Identification Code Codes A0 Manufacturer 0 Device Type 1 Note: 1. The AT27BV256 has the same Product Identification Code as the AT27C256R and AT27LV256A. They are all programming compatible. 0601E–EPROM–12/07 = 13.0 ± 0.25V PP Test Conditions ...
Page 10
... After the byte verifies properly, the next address is selected until all have been checked. V are read again and compared with the original data to determine if the device passes or fails. AT27BV256 10 is raised to 13.0V. Each address is first programmed with one 100 µ then lowered to 5 ...
Page 11
... Plastic J-leaded Chip Carrier (PLCC) 28R 28-lead, 0.330" Wide, Plastic Gull Wing Small Package (SOIC) 28T 28-lead, Plastic Thin Small Outline Package (TSOP) 0601E–EPROM–12/07 Ordering Code AT27BV256-70JI AT27BV256-70RI AT27BV256-70TI Ordering Code AT27BV256-70JU AT27BV256-70RU AT27BV256-70TU Package Type AT27BV256 ...
Page 12
... Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT27BV256 12 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER E1 E ...
Page 13
... Mold Flash or protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R 0601E–EPROM–12/ TITLE 28R, 28-lead, 0.330" Body Width, Plastic Gull Wing Small Outline (SOIC) AT27BV256 COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX SYMBOL NOM A 2.39 – 2.79 A1 0.050 – 0.356 D 18 ...
Page 14
... E Notes: 1. This package conforms to JEDEC reference MO-183. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT27BV256 14 PIN SEATING PLANE A1 TITLE 28T, 28-lead (8 x 13.4 mm) Plastic Thin Small Outline Package, Type I (TSOP) 0º ...
Page 15
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...