AT25160-10PI Atmel, AT25160-10PI Datasheet - Page 8
![IC EEPROM 16KBIT 3MHZ 8DIP](/photos/6/50/65033/313-8-dip_sml.jpg)
AT25160-10PI
Manufacturer Part Number
AT25160-10PI
Description
IC EEPROM 16KBIT 3MHZ 8DIP
Manufacturer
Atmel
Datasheet
1.AT25080-10PI-1.8.pdf
(21 pages)
Specifications of AT25160-10PI
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
16K (2K x 8)
Speed
3MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Functional
Description
8
AT25080/160/320/640
The AT25080/160/320/640 is designed to interface directly with the synchronous serial periph-
eral interface (SPI) of the 6805 and 68HC11 series of microcontrollers.
The AT25080/160/320/640 utilizes an 8-bit instruction register. The list of instructions and their
operation codes are contained in Table 1. All instructions, addresses, and data are transferred
with the MSB first and start with a high-to-low CS transition.
Table 1. Instruction Set for the AT25080/160/320/640
WRITE ENABLE (WREN): The device will power-up in the write disable state when V
applied. All programming instructions must therefore be preceded by a Write Enable
instruction.
WRITE DISABLE (WRDI): To protect the device against inadvertent writes, the Write Disable
instruction disables all programming modes. The WRDI instruction is independent of the sta-
tus of the WP pin.
READ STATUS REGISTER (RDSR): The Read Status Register instruction provides access to
the status register. The READY/BUSY and Write Enable status of the device can be deter-
mined by the RDSR instruction. Similarly, the Block Write Protection bits indicate the extent of
protection employed. These bits are set by using the WRSR instruction.
Table 2. Status Register Format
Table 3. Read Status Register Bit Definition
Instruction Name
WREN
WRDI
RDSR
WRSR
READ
WRITE
Bit
Bit 0 (RDY)
Bit 1 (WEN)
Bit 2 (BP0)
Bit 3 (BP1)
Bits 4 - 6 are 0s when device is not in an internal write cycle.
Bit 7 (WPEN)
Bits 0 - 7 are 1s during an internal write cycle.
WPEN
Bit 7
Bit 6
X
Definition
Bit 0 = 0 (RDY) indicates the device is READY. Bit 0 = 1 indicates the write cycle is
in progress.
Bit 1= 0 indicates the device is not WRITE ENABLED. Bit 1 = 1 indicates the
device is WRITE ENABLED.
See Table 4 on page 9.
See Table 4 on page 9.
See Table 5 on page 9.
Instruction Format
0000 X110
0000 X100
0000 X101
0000 X001
0000 X011
0000 X010
Bit 5
X
Bit 4
X
Bit 3
BP1
Operation
Set Write Enable Latch
Reset Write Enable Latch
Read Status Register
Write Status Register
Read Data from Memory Array
Write Data to Memory Array
Bit 2
BP0
WEN
Bit 1
0675M–SEEPR–9/03
Bit 0
RDY
CC
is