AT24C08-10PC Atmel, AT24C08-10PC Datasheet - Page 22
![IC EEPROM 8KBIT 400KHZ 8DIP](/photos/6/50/65033/313-8-dip_sml.jpg)
AT24C08-10PC
Manufacturer Part Number
AT24C08-10PC
Description
IC EEPROM 8KBIT 400KHZ 8DIP
Manufacturer
Atmel
Datasheet
1.AT24C01A-10PC.pdf
(24 pages)
Specifications of AT24C08-10PC
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
8K (1K x 8)
Speed
400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT24C08-10PC
Manufacturer:
ATMEL
Quantity:
5 510
Company:
Part Number:
AT24C08-10PC
Manufacturer:
MOT
Quantity:
5 510
5TS1 – SOT23
22
NOTES: 1. This drawing is for general information only. Refer to JEDEC Drawing
AT24C01A/02/04/08/16
R
2. Dimension D does not include mold flash, protrusions, or gate burrs.
3. The package top may be smaller than the package bottom. Dimensions
4. These dimensions apply to the flat section of the lead between 0.08 mm
5. Dimension "b" does not include Dambar protrusion. Allowable Dambar
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
MO-193, Variation AB, for additional information.
Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per end.
Dimension E1 does not include interlead flash or protrusion. Interlead
flash or protrusion shall not exceed 0.15 mm per side.
D and E1 are determined at the outermost extremes of the plastic body
exclusive of mold flash, tie bar burrs, gate burrs, and interlead flash, but
including any mismatch between the top and bottom of the plastic body.
and 0.15 mm from the lead tip.
protrusion shall be 0.08 mm total in excess of the "b" dimension at
maximum material condition. The Dambar cannot be located on the lower
radius of the foot. Minimum space between protrusion and an adjacent lead
shall not be less than 0.07 mm.
Seating
Plane
E1
1
5
Top View
b
Side View
TITLE
5TS1, 5-lead, 1.60 mm Body, Plastic Thin Shrink
Small Outline Package (SHRINK SOT)
e1
D
2
e
3
4
A2
E
A1
A
SYMBOL
A
A1
A2
c
D
E
E1
L1
e
e1
b
0.00
0.70
0.08
0.30
COMMON DIMENSIONS
MIN
(Unit of Measure = mm)
–
C
End View
2.90 BSC
2.80 BSC
1.60 BSC
0.60 REF
0.95 BSC
1.90 BSC
NOM
0.90
–
–
–
–
DRAWING NO.
PO5TS1
C
L
L1
1.10
0.10
1.00
0.20
MAX
0.50
0180T–SEEPR–12/04
NOTE
4, 5
2, 3
2, 3
2, 3
4
6/25/03
REV.
A