PLT1M-M00 Panduit Corp, PLT1M-M00 Datasheet - Page 135
![CABLE TIE MINI WR BLK 3.9"](/photos/0/88/8838/plt_series_black_sml.jpg)
PLT1M-M00
Manufacturer Part Number
PLT1M-M00
Description
CABLE TIE MINI WR BLK 3.9"
Manufacturer
Panduit Corp
Series
PAN-TY®r
Type
Locking Cable Tier
Specifications of PLT1M-M00
Color
Black
Wire/cable Tie Type
Standard, Locking
Bundle Diameter
0.87" (22.10mm)
Length
0.325' (99.06mm, 3.90")
Width
0.098" (2.50mm)
Mounting Type
Free Hanging (In-Line)
Tensile Strength
18 lbs. (8.2 kg)
Features
Weather Resistant
Body Material
Nylon 6.6
Operating Temp Range
-40C to 85C
Product Length (mm)
99mm
Product Depth (mm)
4.6mm
Product Height (mm)
3.9mm
Maximum Bundle Diameter
0.87 in
Product
Cable Ties
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Surface Preparation
Epoxy Adhesive Mounts
PANDUIT
containing an equal amount of resin and hardener. Peel the protective covering off and pop the center of the
cup in to form a mixing bowl. Each cup is supplied with a mixer stick and contains enough epoxy to properly
apply three EMS mounts. The resin and hardener should be thoroughly mixed together until the epoxy is a
consistent and uniform color. The mixer stick can then be used to apply the adhesive to the mount. The
epoxy should be forced into the grooves on the bottom of the mount to obtain optimum bond performance.
The mount should be applied to the surface with light pressure and a back-and-forth twisting motion.
Hardening of the epoxy begins five minutes after mixing at room temperature.
Proper Installation Techniques For Pressure Sensitive Adhesive Mounts
Application Chart
Mount Spacing
For specific applications we recommend individual testing prior to production use.
For best results, PANDUIT
recommend that the surface be cleaned prior to mount installation. For rubber and acrylic based foam tape
adhesives, a blend of isopropyl alcohol and water 50/50 may be used to clean most surfaces.
For epoxy type adhesives, especially masonry surfaces, be sure to clean all loose particles away before
mount installation. Some surface abrasion is recommended to achieve maximum strength. A light rubbing
with medium grit emery cloth or sandpaper is best. Wash after abrading.
For proper installation of adhesive mounts with foam tape, simply remove the release liner and place the
mount in the desired location. Avoid touching the adhesive prior to positioning the mount. Apply firm
pressure to the mount for 5 seconds to insure proper adhesion.
Since PANDUIT
backed mounts with a variety of adhesive
types, this chart should be used as a
guideline for choosing the best adhesive
for often-encountered conditions. Each
type of adhesive is rated good, fair or
poor for some specific mounting surfaces
and/or chemical environments.
To determine the number of mounts to
use in a given application, the following
formula can be used as a guideline:
Clean surface with a clean
cloth and isopropyl alcohol.
Cable or weight (lbs./ft.)
Static Load rating of Mount (lbs/mt.)
®
EMA adhesive is a two-part epoxy cement which is packaged in convenient mixer cups
Alcohol
Selection and Use of Adhesive Mounts
®
manufactures adhesive
Allow surface to air dry.
®
adhesive mounts should be applied to clean, dry, grease-free surfaces. We
Remove the release liner,
being careful not to touch
the adhesive.
1. Not recommended for use on copper or brass.
2. Mounts manufactured from outdoor material only. For specific applications, individual testing prior to extensive
use is suggested.
3. Depends on concentration, exposure time and chemical composition.
Plastics
Wood
Glass
Painted Surfaces
Powder Coating
Metal
Paper
Concrete, Stone, Masonry
Chemical Resistance
Water
Oil
Gasoline
Dilute Acids
Dilute Alkalis
Organic Solvents
Outdoor Exposure
=
Surfaces
Spacing
Apply full thumb pressure
for at least 5 seconds.
Foam Tape Mounts
Mounts
Ft.
Not Recommended
Not Recommended
Rubber Based
Good
Good
Good
Good
Good
Good
Good
Good
Poor
Poor
Poor
Poor
Fair
Most commonly used parts appear in BOLD.
1
Foam Tape Mounts
Not Recommended
Acrylic Based
Good
Good
Good
Good
Good
Good
Good
Good
Fair
Fair
Fair
Fair
Fair
Fair
Allow mount to
properly dwell.
3
3
3
3
3
1
9
Adhesive Mounts
Not Recommended
Epoxy Applied
12
6
Good
Good
Good
Good
Good
Good
Good
Good
Poor
Fair
Fair
Fair
Fair
Fair
3
2
135