24LCS61-I/SN Microchip Technology, 24LCS61-I/SN Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
24LCS61-I/SN
Manufacturer Part Number
24LCS61-I/SN
Description
IC EEPROM 1KBIT 400KHZ 8SOIC
Manufacturer
Microchip Technology
Datasheet
1.24LCS61-IP.pdf
(22 pages)
Specifications of 24LCS61-I/SN
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
1K (128 x 8)
Speed
100kHz, 400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Request inventory verification / Request inventory verification
8.0
Read operations are initiated in a similar way as the
write operations. There are three basic types of read
operations: current address read, random read, and
sequential read.
8.1
The 24LCS61/62 contains an address counter that
maintains the address of the last word accessed,
internally incremented by one. Therefore, if the
previous read access was to address n, the next
current address read operation would access data from
address n + 1. Upon receipt of the correct control byte
and ID byte, the 24LCS61/62 issues an acknowledge
and transmits the eight bit data word. The master will
not acknowledge the transfer but does generate a Stop
condition
transmission (Figure 8-1).
8.2
Random read operations allow the master to access
any memory location in a random manner. To perform
this type of read operation, first the word address must
be set. This is done by sending the word address to the
24LCS61/62 as part of a write operation.
FIGURE 8-1:
2004 Microchip Technology Inc.
OE Bit = EDS Pin Output Enable; see Section 9.0 “External Device Select (EDS) Pin and Output Enable (OE) Bit”
READ OPERATIONS
Current Address Read
Random Read
and
the
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
CURRENT ADDRESS READ
24LCS61/62
S
T
A
R
T
S
0
discontinues
1
CONTROL
1 0 O 0 0 1
BYTE
E
A
C
K
ID BYTE
DEVICE
After the ID byte and word address are sent, the master
generates a Start condition following the acknowledge.
This terminates the write operation, but not before the
internal address pointer is set. Then the master sends
the control byte and ID byte for a Read command. The
24LCS61/62 will then issue an acknowledge and
transmits the eight bit data word. The master will not
acknowledge the transfer but does generate a Stop
condition
transmission (Figure 8-2).
8.3
Sequential reads are initiated in the same way as a
random read except that after the 24LCS61/62 trans-
mits the first data byte, the master issues an acknowl-
edge as opposed to a Stop condition in a random
read. This directs the 24LCS61/62 to transmit the next
sequentially addressed 8-bit word (Figure 8-3).
To provide sequential reads the 24LCS61/62 contains
an internal address pointer which is incremented by
one at the completion of each operation. This address
pointer allows the entire memory contents to be serially
read during one operation. The internal address pointer
will automatically roll over from address 7Fh
(24LCS51) or FFh (24LCS62) to address 00h.
24LCS61/24LCS62
Sequential Read
A
C
K
and
DATA
the
24LCS61/62
N
O
A
C
K
S
T
O
P
P
DS21226E-page 13
discontinues