SJ-3518FR (BLACK) 3/4" 3M, SJ-3518FR (BLACK) 3/4" Datasheet - Page 2

• Manufacturer Part Number: SJ-3518FR (BLACK) 3/4"
• Description: LOOP PRESS BACK 3/4"X50'BLK/50FT
• Manufacturer: 3M
• Series: Scotchmate™r

Specifications of SJ-3518FR (BLACK) 3/4"

• Wire/cable Tie Type: Hook and Loop - Loop Strip
• Bundle Diameter: Variable
• Length: 50.0' (15.2m)
• Width: 0.750" (19.1mm)
• Mounting Type: Adhesive
• Color: Black
• Features: -
• Tensile Strength: -
• Other names: Q1414397; SJ3518FRBLACK3/4"

Typical System
Performance
Physical Properties
and Characteristics
3M
SJ3519FR and SJ3518FR
Nylon Flame Resistant Hook and Loop
™
Scotchmate
Note: The following technical information is not product release requirements, but rather represent
Unless stated differently, typical system performance characteristics were measured under controlled
laboratory conditions of 72°F (22°C) and 50% Relative Humidity to obtain maximum reliability. The user
should evaluate products in the actual application to ensure suitable performance for the intended use.
TENSILE (Rigid to Rigid Substrates)
SHEAR (Rigid to Rigid Substrates)
PEEL AND CLEAVAGE
ENGAGED THICKNESS
CLOSURE CYCLE LIFE
SHELF LIFE
Note: Long Term Static Load: Conditions such as temperature variations, engagement area, closure pressure
and vibrations or side-to-side movement after engagement or exposure to prolonged periods of moisture or other
environmental factors can affect the closure strength and long term static load performance. Fasteners may slip or
creep in the direction of the static load forces at temperatures or weights greater than indicated. The user is
responsible for designing the amount of fastening area based upon the specific conditions for the application. Four
square inches of fastening area per pound of static load is suggested as a starting point for such evaluations.
a) System performance tests are determined by measuring the performance of the entire mated reclosable fastener system (two
b) 3M™ Scotchmate™ Reclosable Fasteners SJ3518FR and SJ3519FR are engaged with firm pressure and disengaged, peeled
c) Cycle Life is the number of cycles (openings and closings) the fastener can provide while maintaining 50% or greater of the
d) Shelf life is from date of manufacture when stored in original packaging between 60° to 80°F (16° to 27°C) and 40 to 60%
Dynamic Tensile Engagement Strength
Dynamic Tensile Disengagement
Static Tensile Holding Power
Dynamic Shear (1" x 1" overlap)
Static Shear Holding Power
Peak Cleavage Strength (Rigid to Rigid)
Peak Peel Strength (“T” Peel, Flexible to Flexible)
Peak Peel Strength (90° Peel, Flexible to Rigid)
(Nominal without liner)
non-anodized aluminum plates joined together with the indicated fasteners). The “T” peel, only has the closure performance
measured per ASTM D5170 and was not adhered to aluminum panels. The 90° peel has one of the mated fasteners attached
to a non-anodized aluminum plate while the other mated fastener is disengaged at a 90° angle.
or cleaved at the rate of 12 inches (305 mm) per minute.
original peel values.
relative humidity.
typical performance using standard test methods and is intended for use as a guide to assist in
selection of 3M™ Scotchmate™ Reclosable Fasteners for further evaluation. This technical
information should not be used for setting standards.
TM
Reclosable Fasteners
(d)
(b)
(c)
100°F/100% RH
100°F/100% RH
(b)
(b)
- 2 -
120°F
140°F
158°F
120°F
140°F
158°F
Holds 1.1#/in
Holds 1.1#/in
time in minutes at the indicated temperature
time in minutes at the indicated temperature
Fastener SJ3518FR loop engaged to
Pounds
3M™ Scotchmate™ Reclosable
3M™ Scotchmate™ Reclosable
Pounds
Pounds
Fastener SJ3519FR hook
Inches (mm) ± Tolerance
System Performance
F
/inch width (grams
2
2
F
F
(77.5 grams/cm
(77.5 grams/cm
0.15 (3.9) ± 20%
/sq inch (kNewtons/m
/sq inch (kNewtons/m
< 1.0 (< 6.9)
11.7 (80.7)
18 months
23.4 (162)
5.3 (950)
2.1 (380)
2.0 (360)
5,000
7,000
5,000
2,000
2,000
4,000
4,000
2,000
180
2
2
F
) for indicated
) for indicated
/cm width)
(a)
2
2
):
):