M25P16-VMP6G NUMONYX, M25P16-VMP6G Datasheet - Page 20
![IC FLASH 16MBIT 75MHZ 8VFQFPN](/photos/7/28/72850/m25p16-vmp6g_sml.jpg)
M25P16-VMP6G
Manufacturer Part Number
M25P16-VMP6G
Description
IC FLASH 16MBIT 75MHZ 8VFQFPN
Manufacturer
NUMONYX
Series
Forté™r
Datasheet
1.M25P16-VMN6P.pdf
(59 pages)
Specifications of M25P16-VMP6G
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
16M (2M x 8)
Speed
75MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-VFQFN, 8-VFQFPN
Clock Frequency
75MHz
Supply Voltage Range
2.7V To 3.6V
Memory Case Style
VFQFPN
No. Of Pins
8
Operating Temperature Range
-40°C To +85°C
Memory Configuration
2M X 8
Interface Type
Serial, SPI
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M25P16-VMP6G
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Part Number:
M25P16-VMP6G
Manufacturer:
ST
Quantity:
20 000
6.3
Note:
Table 5.
Figure 10. Read Identification (RDID) instruction sequence and data-out sequence
20/59
Manufacturer
identification
20h
Read Identification (RDID)
The Read Identification (RDID) instruction allows to read the device identification data:
The manufacturer identification is assigned by JEDEC, and has the value 20h for Numonyx.
The device identification is assigned by the device manufacturer, and indicates the memory
type in the first byte (20h), and the memory capacity of the device in the second byte (15h).
The UID contains the length of the following data in the first byte (set to 10h), and 16 bytes
of the optional Customized Factory Data (CFD) content. The CFD bytes are read-only and
can be programmed with customers data upon their request. If the customers do not make
requests, the devices are shipped with all the CFD bytes programmed to zero (00h).
See
devices.
Any Read Identification (RDID) instruction while an Erase or Program cycle is in progress, is
not decoded, and has no effect on the cycle that is in progress.
The device is first selected by driving Chip Select (S) Low. Then, the 8-bit instruction code
for the instruction is shifted in. After this, the 24-bit device identification, stored in the
memory, the 8-bit CFD length followed by 16 bytes of CFD content will be shifted out on
Serial Data output (Q). Each bit is shifted out during the falling edge of Serial Clock (C).
The instruction sequence is shown in
sequence and data-out
by driving Chip Select (S) High at any time during data output.
When Chip Select (S) is driven High, the device is put in the Standby Power mode. Once in
the Standby Power mode, the device waits to be selected, so that it can receive, decode and
execute instructions.
Read Identification (RDID) data-out sequence
Section 12: Ordering Information, Standard Parts on page 53
Manufacturer identification (1 byte)
Device identification (2 bytes)
A Unique ID code (UID) (17 bytes, of which 16 available upon customer request).
Memory type
20h
Device identification
sequence. The Read Identification (RDID) instruction is terminated
Memory capacity
15h
Figure 10: Read Identification (RDID) instruction
CFD length
10h
for CFD programmed
UID
CFD content
16 bytes