M27C256B-15C1 STMicroelectronics, M27C256B-15C1 Datasheet - Page 10
![IC OTP 256KBIT 150NS 32PLCC](/photos/7/23/72383/497-32-plcc_series_sml.jpg)
M27C256B-15C1
Manufacturer Part Number
M27C256B-15C1
Description
IC OTP 256KBIT 150NS 32PLCC
Manufacturer
STMicroelectronics
Datasheet
1.M27C256B-15F1.pdf
(24 pages)
Specifications of M27C256B-15C1
Format - Memory
EPROMs
Memory Type
OTP EPROM
Memory Size
256K (32K x 8)
Speed
150ns
Interface
Parallel
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Package / Case
32-PLCC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-1649-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M27C256B-15C1
Manufacturer:
ST
Quantity:
6
Company:
Part Number:
M27C256B-15C1
Manufacturer:
ST
Quantity:
5 510
Company:
Part Number:
M27C256B-15C1
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
M27C256B-15C1
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
M27C256B-15C1E
Manufacturer:
ST
Quantity:
6
Company:
Part Number:
M27C256B-15C1E5
Manufacturer:
ST
Quantity:
10
Device operation
2.7
2.8
2.9
10/24
Figure 4.
Program inhibit
Programming of multiple M27C256Bs in parallel with different data is also easily
accomplished. Except for E, all like inputs including G of the parallel M27C256B may be
common. A TTL low level pulse applied to a M27C256B's E input, with V
program that M27C256B. A high level E input inhibits the other M27C256Bs from being
programmed.
Program Verify
A verify (read) should be performed on the programmed bits to determine that they were
correctly programmed. The verify is accomplished with G at V
V
Electronic signature
The Electronic Signature (ES) mode allows the reading out of a binary code from an
EPROM that will identify its manufacturer and type. This mode is intended for use by
programming equipment to automatically match the device to be programmed with its
corresponding programming algorithm. The ES mode is functional in the 25°C ± 5°C
ambient temperature range that is required when programming the M27C256B. To activate
the ES mode, the programming equipment must force 11.5V to 12.5V on address line A9 of
the M27C256B, with V
device outputs by toggling address line A0 from V
held at V
code and byte 1 (A0 = V
M27C256B, these two identifier bytes are given in
Q7 to Q0.
CC
at 6.25V.
IL
during Electronic Signature mode. Byte 0 (A0 = V
Programming flowchart
CC
IH
= V
) the device identifier code. For the STMicroelectronics
YES
NO
PP
FAIL
= 25
++n
= 5V. Two identifier bytes may then be sequenced from the
V CC = 6.25V, V PP = 12.75V
CHECK ALL BYTES
NO
2nd: V CC = 4.2V
E = 100 s Pulse
1st: V CC = 6V
VERIFY
n = 0
Addr
Last
YES
YES
IL
NO
Table 3
to V
++ Addr
IH
. All other address lines must be
and can be read-out on outputs
AI00760B
IL
IL
) represents the manufacturer
, E at V
IH
, V
PP
PP
at 12.75V, will
at 12.75V and
M27C256B