M25P80-VMN6TP NUMONYX, M25P80-VMN6TP Datasheet - Page 33
![IC FLASH 8MBIT 75MHZ 8SOIC](/photos/7/28/72830/m25p80-vmn6tp_sml.jpg)
M25P80-VMN6TP
Manufacturer Part Number
M25P80-VMN6TP
Description
IC FLASH 8MBIT 75MHZ 8SOIC
Manufacturer
NUMONYX
Series
Forté™r
Datasheet
1.M25P80-VMP6G.pdf
(57 pages)
Specifications of M25P80-VMN6TP
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
8M (1M x 8)
Speed
75MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Package
8SOIC N
Cell Type
NOR
Density
8 Mb
Architecture
Sectored
Block Organization
Symmetrical
Typical Operating Supply Voltage
3.3 V
Sector Size
64KByte x 16
Timing Type
Synchronous
Interface Type
Serial-SPI
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
M25P80-VMN6TP
M25P80-VMN6TPTR
Q3580447
M25P80-VMN6TPTR
Q3580447
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M25P80-VMN6TP
Manufacturer:
Numonyx
Quantity:
22 500
Company:
Part Number:
M25P80-VMN6TP
Manufacturer:
MICRON44
Quantity:
2 163
Part Number:
M25P80-VMN6TP
Manufacturer:
ST
Quantity:
20 000
6.11
Deep Power-down (DP)
Executing the Deep Power-down (DP) instruction is the only way to put the device in the
lowest consumption mode (the Deep Power-down mode). It can also be used as an extra
software protection mechanism, while the device is not in active use, since in this mode, the
device ignores all Write, Program and Erase instructions.
Driving Chip Select (S) High deselects the device, and puts the device in the Standby mode
(if there is no internal cycle currently in progress). But this mode is not the Deep Power-
down mode. The Deep Power-down mode can only be entered by executing the Deep
Power-down (DP) instruction, to reduce the standby current (from I
in
Once the device has entered the Deep Power-down mode, all instructions are ignored
except the Release from Deep Power-down and Read Electronic Signature (RES)
instruction. This releases the device from this mode. The Release from Deep Power-down
and Read Electronic Signature (RES) instruction also allows the Electronic Signature of the
device to be output on Serial Data Output (Q).
The Deep Power-down mode automatically stops at Power-down, and the device always
Powers-up in the Standby mode.
The Deep Power-down (DP) instruction is entered by driving Chip Select (S) Low, followed
by the instruction code on Serial Data Input (D). Chip Select (S) must be driven Low for the
entire duration of the sequence.
The instruction sequence is shown in
Chip Select (S) must be driven High after the eighth bit of the instruction code has been
latched in, otherwise the Deep Power-down (DP) instruction is not executed. As soon as
Chip Select (S) is driven High, it requires a delay of t
to I
Any Deep Power-down (DP) instruction, while an Erase, Program or Write cycle is in
progress, is rejected without having any effects on the cycle that is in progress.
Figure 17. Deep Power-down (DP) instruction sequence
Table
S
C
D
CC2
and the Deep Power-down mode is entered.
14).
0
1
2
Instruction
3
4
5
6
Figure
7
17.
DP
Stand-by Mode
t
DP
before the supply current is reduced
CC1
Deep Power-down Mode
to I
CC2
, as specified
AI03753D
33/57