UMFT240XE-01 FTDI, UMFT240XE-01 Datasheet - Page 5
![no-image](/images/no-image-200.jpg)
UMFT240XE-01
Manufacturer Part Number
UMFT240XE-01
Description
Interface Development Tools USB to 8-Bit 245 FIFO Module
Manufacturer
FTDI
Type
USB to FIFOr
Series
FT240Xr
Datasheet
1.UMFT240XE-01.pdf
(18 pages)
Specifications of UMFT240XE-01
Rohs
yes
Product
Development Modules
Tool Is For Evaluation Of
FT240XQ
Interface Type
I2C, FIFO, USB
Operating Supply Voltage
3.3 V
Description/function
USB to 8bit 245 FIFO evaluation module
Dimensions
29.02 mm x 19.24 mm x 9.2 mm
Operating Supply Current
1 A
Factory Pack Quantity
25
For Use With
FT240XQ
4.2
Pin No.
J1-1, J1-7,
J2-5
J1-2
J1-3
J1-4
J1-5
J1-6
J1-8
J1-9
J1-10
J1-11
J1-12
J2-1
J2-2
J2-3
J2-4
J2-5
J2-6
J2-8
J2-9
J2-10
J2-11
J2-12
Table 4.1 – Module Pin Out Description
Signal Descriptions
Name
GND
3V3OUT
VCCIO
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
SLD
VBUS
VCC
RESET#
CBUS6
CBUS5
SI/WU
WR#
RD#
TXE#
RXF#
Type
PWR
Power
Input/
Output
Power
Input
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
GND
Power
Output
Power
Input
Input
I/O
I/O
Output
Input
Input
Output
Output
Description
Module Ground Supply Pins
3.3V output from integrated LDO regulator. This pin is decoupled with a 100nF
capacitor to ground on the PCB module. The prime purpose of this pin is to
provide the 3.3V supply that can be used internally. For power supply
configuration details see section 5.
+1.8V to +3.3V supply to the UART Interface and CBUS I/O pins. For power
supply configuration details see section 5.
245 FIFO Bi-Directional data bit 7.
245 FIFO Bi-Directional data bit 6.
245 FIFO Bi-Directional data bit 5.
245 FIFO Bi-Directional data bit 4.
245 FIFO Bi-Directional data bit 3.
245 FIFO Bi-Directional data bit 2.
245 FIFO Bi-Directional data bit 1.
245 FIFO Bi-Directional data bit 0.
USB Cable Shield. Connected to GND via a 0ohm resistor.
5V Power output from the USB bus. For a low power USB bus powered design, up
to 100mA can be sourced from the 5V supply and applied to the USB bus. A
maximum of 500mA can be sourced from the USB bus in a high power USB bus
powered design. Currents up to 1A can be sourced from a dedicated charger and
applied to the USB bus.
5V power input for FT240X. For power supply configuration details see section 5.
FT231X active low reset line. Configured with an on board pull-up and
recommended filter capacitor. When no power is applied to the USB bus reset, will
be held low, this prevents current from flowing to the host or hub when in self-
powered mode.
Configurable CBUS I/O Pin. Function of this pin is configured in the device internal
MTP ROM. Factory Default pin Function is
Table 4.2.
Configurable CBUS I/O Pin. Function of this pin is configured in the device internal
MTP ROM. Factory Default pin Function is VBUS_Sense. See CBUS Signal Options,
Table 4.2.
Send Immediate/Wake Up
245 FIFO Write status line
245 FIFO Read status line
245 FIFO Transmit control line
245 FIFO Receive control line
Copyright © 2012 Future Technology Devices International Limited
Document Reference No.: FT_000653
Keep_Awake.
See CBUS Signal Options,
Clearance No.: FTDI#
5
UMFT240XE
Version 1.0
295