AS3935-DK ams, AS3935-DK Datasheet
AS3935-DK
Manufacturer Part Number
AS3935-DK
Description
Touch Sensor Development Tools
Manufacturer
ams
Datasheet
1.AS3935-DK.pdf
(2 pages)
Specifications of AS3935-DK
Tool Is For Evaluation Of
AS3935
Operating Current
3 V
AS3935 Demo Kit
Quick Start Manual
AS3935
Franklin Lightning Sensor and Lightning Emulator
Demo Kit
Procedure
www.austriamicrosystems.com
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. It is possible to monitor all lightning events in a history. All lightning and its point of time will be stored in
Insert the 3V battery (CR2032) in the battery holder on the AS3935 demo board.
Insert a 3V battery in the battery holder on the Lightning Emulator.
Position the lightning emulator and the AS3935 demo board in such a way that both antennas are in
parallel to each other. Keep a distance of 10-15 cm between both boards.
Turn on the AS3935 Lightning Sensor via the ON/OFF – switch. When you switch on the board you will
see on the LCD the austriamicrosystems logo followed by the LCO and the RCO calibration. After
successful calibration the AS3935 goes into sense mode awaiting a lightning.
Turn on the Lightning Emulator via the ON/OFF – switch. When turned on, the blue LED will be flashing
up once a second.
Now you can start pressing the switches, far strike, mid strike and close strike on the Emulator,
simulating a lightning which will be detected by the sensor. The display on the AS3935-DB will flash up
and highlight “Lightning detected” and the distance to the head of the storm. Furthermore the sensor
informs if the storm is approaching or departing via the internal statistical analysis. Lightning will be
alarmed with the buzzer signal.
The internal statistics can be cleared via a long-press (>1s) on the yellow button of the AS3935-DB.
If the Disturber button is pressed, the AS3935 demo board will show “Disturber detected”.
If the Noise button is pressed, the AS3935 demo board will show “Noise Level too high”.
a volatile memory. The actual time can be seen on the LCD applying a short press on the yellow button.
The time can be adjusted via the GUI, as well as the history read out and deleted.
Revision 1.00
~10 cm
1 - 2
Related parts for AS3935-DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Interface - Specialized
Manufacturer:
ams
Datasheet:
Part Number:
Description:
Magnetic / Reed Switches 3/4 GAP MINI CONTCT N.C. BROWN
Manufacturer:
AMSECO
Part Number:
Description:
Magnetic / Reed Switches MAGNET ONLY
Manufacturer:
AMSECO
Part Number:
Description:
Magnetic / Reed Switches SPACER FOR AMS38/39
Manufacturer:
AMSECO
Part Number:
Description:
Magnetic / Reed Switches COVER FOR AMS3839 BROWN
Manufacturer:
AMSECO
Part Number:
Description:
Magnetic / Reed Switches SPACER FOR AMS38/39 BROWN
Manufacturer:
AMSECO
Part Number:
Description:
AND / OR circuit providing the logical function Q
Manufacturer:
AMS
Datasheet:
Part Number:
Description:
Analog to Digital Converters - ADC
Manufacturer:
ams
Datasheet:
Part Number:
Description:
Interface - Specialized
Manufacturer:
ams
Datasheet:
Part Number:
Description:
Interface - Specialized Ambient Light Sensor Light to Digital
Manufacturer:
ams
AS3935-DK Summary of contents
Page 1
... Keep a distance of 10-15 cm between both boards. 4. Turn on the AS3935 Lightning Sensor via the ON/OFF – switch. When you switch on the board you will see on the LCD the austriamicrosystems logo followed by the LCO and the RCO calibration. After successful calibration the AS3935 goes into sense mode awaiting a lightning. ...
Page 2
... AS3935 Franklin Lightning Sensor and Lightning Emulator Copyright Copyright © 1997-2012, austriamicrosystems AG, Tobelbaderstraße 30, 8141 Unterpremstätten - Graz, Austria - Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. ...