XBIB-U-SP Digi International, XBIB-U-SP Datasheet - Page 32

• Manufacturer Part Number: XBIB-U-SP
• Description: Interface Development Tools USB/Xbee/Xbee-Pro Inf Brd SMT Pads
• Manufacturer: Digi International
• Type: USB to XBee / XBee-PROr

Specifications of XBIB-U-SP

• Rohs: yes
• Product: Development Boards
• Tool Is For Evaluation Of: XBee / XBee-PRO
• Interface Type: USB
• Operating Supply Voltage: 5 V

Table 3‐06. XBee‐PRO Commands ‐ I/O Settings (sub‐category designated within {brackets})
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
Diagnostics
Table 3‐07. XBee/XBee‐PRO Commands ‐ Diagnostics
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
XBee/XBee‐PRO™ OEM RF Modules ‐ 802.15.4 ‐ v1.xAx [2007.05.031]
AT
Command
IA (v1.xA0*)
T0 - T7
(v1.xA0*)
P0
P1 (v1.xA0*)
M0 (v1.xA0*)
M1 (v1.xA0*)
PT (v1.xA0*)
RP
AT
Command
VR
VL (v1.x80*)
HV (v1.x80*)
DB
EC (v1.x80*)
EA (v1.x80*)
ED (v1.x80*)
Command
Category
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
Command
Category
Diagnostics
Diagnostics
Diagnostics
Diagnostics
Diagnostics
Diagnostics
Diagnostics
Name and Description
I/O Input Address. Set/Read addresses of module to which outputs are bound. Setting
all bytes to 0xFF will not allow any received I/O packet to change outputs. Setting
address to 0xFFFF will allow any received I/O packet to change outputs.
(D0 - D7) Output Timeout. Set/Read Output timeout values for lines that correspond
with the D0 - D7 parameters. When output is set (due to I/O line passing) to a non-
default level, a timer is started which when expired will set the output to it default level.
The timer is reset when a valid I/O packet is received.
PWM0 Configuration. Select/Read function for PWM0 pin.
PWM1 Configuration. Select/Read function for PWM1 pin.
PWM0 Output Level. Set/Read the PWM0 output level.
PWM1 Output Level. Set/Read the PWM0 output level.
PWM Output Timeout. Set/Read output timeout value for both PWM outputs. When
PWM is set to a non-zero value: Due to I/O line passing, a time is started which when
expired will set the PWM output to zero. The timer is reset when a valid I/O packet is
received.]
RSSI PWM Timer. Set/Read PWM timer register. Set the duration of PWM (pulse width
modulation) signal output on the RSSI pin. The signal duty cycle is updated with each
received packet and is shut off when the timer expires.]
Name and Description
Firmware Version. Read firmware version of the RF module.
Firmware Version - Verbose. Read detailed version information (including application
build date, MAC, PHY and bootloader versions).
Hardware Version. Read hardware version of the RF module.
Received Signal Strength. Read signal level [in dB] of last good packet received
(RSSI). Absolute value is reported. (For example: 0x58 = -88 dBm) Reported value is
accurate between -40 dBm and RX sensitivity.
CCA Failures. Reset/Read count of CCA (Clear Channel Assessment) failures. This
parameter value increments when the module does not transmit a packet because it
detected energy above the CCA threshold level set with CA command. This count
saturates at its maximum value. Set count to “0” to reset count.
ACK Failures. Reset/Read count of acknowledgment failures. This parameter value
increments when the module expires its transmission retries without receiving an ACK
on a packet transmission. This count saturates at its maximum value. Set the parameter
to “0” to reset count.
Energy Scan. Send ‘Energy Detect Scan’. ED parameter determines the length of scan
on each channel. The maximal energy on each channel is returned and each value is
followed by a carriage return. Values returned represent detected energy levels in units
of -dBm. Actual scan time on each channel is measured as Time = [(2 ^ SD) * 15.36]
ms. Total scan time is this time multiplied by the number of channels to be scanned.
© 2007 MaxStream, Inc.
Chapter 3 ‐ RF Module Configuration
Parameter Range
0 - 0xFFFFFFFFFFFFFFFF
0 - 0xFF [x 100 ms]
0 - 2
0 - 2
0 - 0x03FF
0 - 0x03FF
0 - 0xFF [x 100 ms]
0 - 0xFF [x 100 ms]
Parameter Range
0 - 0xFFFF [read-only]
-
0 - 0xFFFF [read-only]
0x17-0x5C (XBee)
0x24-0x64 (XBee-PRO)
[read-only]
0 - 0xFFFF
0 - 0xFFFF
0 - 6
0 = Disabled
1 = RSSI
2 = PWM Output
0 = Disabled
1 = RSSI
2 = PWM Output
Default
0xFFFFFFF
FFFFFFFFF
0xFF
1
0
-
-
0xFF
0x28 (40d)
Default
Factory-set
-
Factory-set
-
-
-
-
32