MAX14830EVKIT# Maxim Integrated, MAX14830EVKIT# Datasheet - Page 2

• Manufacturer Part Number: MAX14830EVKIT#
• Description: Interface Development Tools MAX14830 Eval Kit
• Manufacturer: Maxim Integrated
• Type: UARTr
• Series: MAX14830r

Specifications of MAX14830EVKIT#

• Rohs: yes
• Product: Evaluation Kits
• Tool Is For Evaluation Of: MAX14830
• Interface Type: I2C, RS-232, RS-485, SPI
• Operating Supply Voltage: 3.3 V, 24 V
• Operating Supply Current: 100 mA

Note: Indicate that you are using the MAX14830 when contacting these component suppliers.
The EV kit is fully assembled and tested. Follow the steps
below to verify board operation. Caution: Do not turn on
the power supply until all connections are completed.
1)
2)
•
•
•
•
DESIGNATION
Diodes Incorporated
IRC, Inc.
KEMET Corp.
Murata Electronics North America, Inc.
Semtech Corporation
TDK Corp.
MAX14830 EV kit
User-supplied SPI interface controller
+3.3V, 100mA DC power supply
+24V, 100mA DC power supply
Verify that shunts are installed in their default
positions, as shown in Table 1.
Connect the output of the SPI interface controller to
the SPI/I2C 12-pin header, as follows:
• Connect CSN to pin 5 of SPI/I2C
• Connect MISO to pin 6 of SPI/I2C
• Connect SCLK to pin 7 of SPI/I2C
• Connect MOSI to pin 10 of SPI/I2C
U2, U3
U4–U7
SW1
U1
SUPPLIER
QTY
1
1
2
4
Momentary pushbutton switch
Quad SPI/I
128-word FIFOs (48 TQFN-EP)
Maxim MAX14830ETM+
Quad DPDT switches
(36 TQFN-EP)
Maxim MAX4761ETX+
IO-Link master transceivers
(24 TQFN-EP)
Maxim MAX14824GTG+
Required Equipment
DESCRIPTION
2
C UART with
Quick Start
Procedure
805-446-4800
361-992-7900
864-963-6300
770-436-1300
805-495-2111
847-803-6100
PHONE
3)
4)
5)
6)
7)
8)
9)
10) The EV kit is now ready for additional testing.
DESIGNATION
U8–U11
Turn on the +3.3V power supply and set the supply
to +3.3V, then disable the power supply.
Connect the positive terminal of the +3.3V power
supply to the +3.3V PCB pad on the EV kit. Connect
the negative terminal of the power supply to the
GND PCB pad.
Turn on the +24V power supply and set the supply
to +24V, then disable the power supply.
Connect the positive terminal of the +24V power
supply to the +24V PCB pad on the EV kit. Connect
the negative terminal of the power supply to the
GND PCB pad.
Enable both power supplies.
Send SPI signals to the EV kit through the SPI/I2C
12-pin header.
Detect the output at the IOLINK1–IOLINK4 4-pin
headers.
Evaluates: MAX14830
U12
Y1
—
—
Component List (continued)
www.diodes.com
www.irctt.com
www.kemet.com
www.murata-northamerica.com
www.semtech.com
www.component.tdk.com
QTY
19
4
1
1
1
Component Suppliers
Multiprotocol transceivers
(20 SSOP)
Maxim MAX3160EEAP+
SPDT analog switch (6 SOT23)
Maxim MAX4624EUT+
(Top Mark: AADL)
3.6864MHz crystal
Shunts
PCB: MAX14830 EVALUATION
KIT
WEBSITE
DESCRIPTION
2