GLS85LP1016B-M-I-44CN-ED000 Greenliant, GLS85LP1016B-M-I-44CN-ED000 Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/2/284/greenliant_sml.jpg)
GLS85LP1016B-M-I-44CN-ED000
Manufacturer Part Number
GLS85LP1016B-M-I-44CN-ED000
Description
Memory IC Development Tools 16GByte NANDrv Eval Brd / 44-pin ATA Con
Manufacturer
Greenliant
Datasheet
1.GLS85LP1004B-M-C-LFTE_REV._CB0.pdf
(11 pages)
Specifications of GLS85LP1016B-M-I-44CN-ED000
Rohs
yes
Table 3-1: Pin Assignments (1 of 2)
These specifications are subject to change without notice.
© 2013 Greenliant Systems
GLS85LP1002A / 1004B / 1008B / 1016B / 1032A
Industrial / Commercial Temp
DMACK#
Host Side Interface
DMARQ
CS1FX#
CS3FX#
Symbol
IOWR#
IORD#
CSEL
D15
D14
D13
D12
D11
D10
A2
A1
A0
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Pin No.
91-Ball
G9
G8
G3
G2
K8
K3
H8
H7
E8
H4
E3
H3
K2
H2
H9
L2
F9
F8
F7
F4
F3
F2
L3
L8
L9
J3
Type
Pin
I/O
O
I
I
I
I
I
I
PATA NANDrive™
I/O Type
I1Z/O2
I2U
I1U
I1Z
I2Z
I2Z
I2Z
O2
A[2:0] are used to select one of eight registers in the Task File.
D[15:0] Data bus
DMA Acknowledge - input from Host
DMA Request to Host
CS1FX# is the chip select for the task file registers
CS3FX# is used to select the alternate status register and the Device
Control register.
This internally pulled-up signal is used to configure this device as a
Master or a Slave. When this pin is grounded, this device is configured
as a Master. When the pin is open, this device is configured as a
Slave. The pin setting should remain the same from Power-on to
Power-down.
IORD#: This is an I/O Read Strobe generated by the Host. When Ultra
DMA mode is not active, this signal gates I/O data from the device.
(This pin supports three functions)
HDMARDY#: In Ultra DMA mode when DMA Read is active, this
signal is asserted by the Host to indicate that the Host is ready to
receive Ultra DMA data-in bursts. The Host may negate HDMARDY#
to pause an Ultra DMA transfer.
HSTROBE: When DMA Write is active, this signal is the data-out
strobe generated by the Host. Both the rising and falling edges of
HSTROBE cause data to be latched by the device. The Host may stop
generating HSTROBE edges to pause an Ultra DMA data-out burst.
IOWR#: This is an I/O Write Strobe generated by the Host. When
Ultra DMA mode is not active, this signal is used to clock I/O data into
the device. (This pin supports two functions)
STOP: When Ultra DMA mode protocol is active, the assertion of this
signal causes the termination of the Ultra DMA burst
4
Name and Functions
Fact Sheet 02.001
February 2013
02/12/2013
S71441-F