AT27C020-90PU Atmel, AT27C020-90PU Datasheet
AT27C020-90PU
Specifications of AT27C020-90PU
Available stocks
Related parts for AT27C020-90PU
AT27C020-90PU Summary of contents
Page 1
... OE) to give designers the flexibility to prevent bus contention. With 256K bytes storage capability, the AT27C020 allows firmware to be stored reli- ably and to be accessed by the system without the delays of mass storage media. Atmel’s AT27C020 has additional features to ensure high quality and efficient produc- tion use ...
Page 2
... A16 2 31 A15 3 30 A12 GND 16 17 AT27C020 2 Function Addresses Outputs Chip Enable Output Enable Program Strobe 2.3 A11 A14 A13 28 A13 A14 27 A8 A17 26 A9 PGM 25 A11 VCC 24 OE VPP 23 A10 A16 22 CE A15 21 07 A12 VCC PGM A17 A14 ...
Page 3
... Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the (1) operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device (1) reliability. (1) AT27C020 3 ...
Page 4
... High High High Identification Code and A0, which is toggled select the Device Code byte. AT27C020 -55 -90 -40° 85° C -40° 85° C -40° 125° ± 10% 5V ± 10% Min Max ±1.0 ±5.0 ±10 100 1.0 25 -0.6 0.8 2 0.5 CC 0.4 2 0570G–EPROM–12/07 ...
Page 5
... This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. 0570G–EPROM–12/07 Condition ( after the falling edge of CE without impact after the address is valid without impact on t ACC OE AT27C020 AT27C020 -55 -90 Min Max Min Max ACC ...
Page 6
... Output Test Load Note: 13. Pin Capacitance ( MHz 25° C Symbol Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27C020 6 3.0V AC 1.5V 0. 100 pF including jig capacitance except -55 devices, where pF. Max MEASUREMENT LEVEL Units Conditions ...
Page 7
... Programming Waveforms Notes: 1. The Input Timing reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27C020, a 0.1 µF capacitor is required across V 0570G–EPROM–12/07 (1) and 2.0V for AT27C020 and ground to suppress voltage transients. ...
Page 8
... CC 2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven – see timing diagram. 3. Program Pulse width tolerance is 100 µs ± 5%. 17. Atmel’s AT27C020 Integrated Product Identification Code Codes A0 O7 Manufacturer ...
Page 9
... V are read again and compared with the original data to determine if the device passes or fails. 0570G–EPROM–12/07 is raised to 13.0V. Each address is first programmed with one 100 µ then lowered to 5.0V and V PP AT27C020 5.0V. All bytes CC 9 ...
Page 10
... AT27C020-55JI AT27C020-55PI AT27C020-55TI 0.1 AT27C020-90JI AT27C020-90PI AT27C020-90TI 0.1 AT27C020-90JA AT27C020-90PA Ordering Code 0.1 AT27C020-55JU AT27C020-55PU AT27C020-55TU 0.1 AT27C020-90JU AT27C020-90PU AT27C020-90TU Package Type Package Operation Range 32J Industrial 32P6 (-40° 85° C) 32T 32J Industrial 32P6 (-40° 85° C) 32T 32J Automotive 32P6 (-40° ...
Page 11
... Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0570G–EPROM–12/07 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER TITLE 32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC) AT27C020 0.318(0.0125) 0.191(0.0075 COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 3.175 – ...
Page 12
... PDIP A SEATING PLANE Note: 1. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R AT27C020 12 D PIN 0º ~ 15º REF eB TITLE 32P6, 32-lead (0.600"/15.24 mm Wide) Plastic Dual ...
Page 13
... Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0570G–EPROM–12/07 PIN SEATING PLANE A1 TITLE 32T, 32-lead ( Package) Plastic Thin Small Outline Package, Type I (TSOP) AT27C020 0º ~ 8º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – ...
Page 14
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...