ATSAM4S-XSTK Atmel, ATSAM4S-XSTK Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
ATSAM4S-XSTK
Manufacturer Part Number
ATSAM4S-XSTK
Description
Development Boards & Kits - ARM SAM4S Xplained Pro Starter Kit
Manufacturer
Atmel
Datasheet
1.ATSAM4S-XSTK.pdf
(21 pages)
Specifications of ATSAM4S-XSTK
Product
Starter Kits
Tool Is For Evaluation Of
Xplained Pro
Core
ARM Cortex M4
Interface Type
USB
Operating Supply Voltage
4.4 V to 5 V
Data Bus Width
8 bit, 32 bit
Description/function
For evaluation and prototyping with SAM4S
For Use With
Xplained Pro
3.3
Note
3.3.1
Warning
3.4
3.4.1
Power supply
The SAM4S Xplained Pro kit can be powered either by USB or by an external power source through the 4-
pin power header, marked PWR. This connector is described in
power sources and specifications are listed in
Table 3.3. Power sources for SAM4S Xplained Pro
The kit will automatically detect which power sources are available and choose which one to use according to
the following priority:
1. External power
2. Embedded debugger USB
3. Target USB
Measuring SAM4S power consumption
As part of an evaluation of the SAM4S it can be of interest to measure its power consumption. Because the
device has a separate power plane (VCC_MCU_P3V3) on this board it is possible to measure the current
consumption by measuring the current that is flowing into this plane. The VCC_MCU_P3V3 plane is connected
via a jumper to the main power plane (VCC_TARGET_P3V3) and by replacing the jumper with an ampere
meter it is possible to determine the current consumption. To locate the current measurement header, please
refer to
Standard headers and connectors
Xplained Pro extension header
All Xplained Pro kits have one or more dual row, 20 pin, 100mil extension headers. Xplained Pro MCU boards
have male headers while Xplained Pro extensions have their female counterparts. Note that all pins are
not always connected. However, all the connected pins follow the defined pin-out described in
“Xplained Pro extension
Data Field
Maximum Voltage [mV]
Maximum Current [mA]
Power input
External power
Embedded debugger
USB
Target USB
External power is required when the 500mA through the USB connector is not enough to power a
connected USB device in a USB host application.
Do not power the board without having the jumper or an ampere meter mounted. This can cause
the SAM4S to be powered through its I/O pins and cause undefined operation of the device.
Figure 1.1, “SAM4S Xplained Pro evaluation kit
header”. The extension headers can be used to connect a wide variety of Xplained Pro
Voltage requirements
5 V +/- 2 % (+/- 100 mV)
for USB host operation.
4.3 V to 5.5 V if USB
host operation is not
required
4.4V to 5.25V
(according to USB spec)
4.4V to 5.25V
(according to USB spec)
Data Type
uint16_t
uint16_t
Table 3.3, “Power sources for SAM4S Xplained
overview”.
Current requirements
Recommended
minimum is 1A to be
able to provide enough
current for connected
USB devices and the
board itself.
Recommended
maximum is 2A due
to the input protection
maximum current
specification.
500 mA (according to
USB spec)
500 mA (according to
USB spec)
Atmel SAM4S Xplained Pro [USER GUIDE]
Atmel-42075B-MCU-Atmel SAM4S Xplained Pro-USER GUIDE-03/2013
Example Content
3600
30
“Power header” on page
Connector marking
PWR
DEBUG USB
TARGET USB
10. The available
Pro”.
Table 3.4,
7