KIT 79879-3 Digital View, KIT 79879-3 Datasheet

Page 1

PC, DVI, VIDEO, HD Component INTERFACE CONTROLLER CONTENTS Page: 2. Introduction, How to Proceed, Usage Note, Disclaimer 3. System design – Diagram of a suggested system 4. Assembly notes – Important information about system elements 6. Connection & Operation – ...

Page 2

Introduction Designed for LCD monitor and other flat panel display applications, the SVH-1920 is a feature rich interface controller for : TFT (active matrix) LCD panels of 1920x1200, 1920x1080, 1600x1200, 1680x1050, 1440x900, 1366x768, 1280x1024, 1280x800, 1280x768 1024x768, 800x600, 800x480 and ...

Page 3

... Interface for connection with to HD-SDI adaptor board 21. +12V / +24V DC power input 22. External panel power input 23. Auxiliary video input 24. Auxiliary +5VDC, max 500mA output 25. Ambient light sensor connection 26. Backlight status input Digital View provides a range of parts, such as listed above, to make up complete display solutions. 3 ...

Page 4

ASSEMBLY NOTES This controller is designed for monitor and custom display projects using 1920x1200 or 1920x1080 or 1600x1200 or 1680x1050 or 1440x900 or 1366x768 or 1280 x 1024 or 1024 x 768 or 800x600 or 640x480 resolution TFT panels with ...

Page 5

Interface for connecting to HD-SDI adaptor board HD-SDI (1-in-1-out) adaptor board, Kit number P/N 546013410-3 includes : HD-1000 adaptor (1-in-1-out) Ribbon cable HD-SDI (2-in-2-out) adaptor board, Kit number P/N 546013310-3 includes : HD-2000 adaptor (2-in-2-out) Ribbon cable 21. Power ...

Page 6

CONNECTION & OPERATION CAUTION: Never connect or disconnect parts of the display system when the system is powered up as this may cause serious damage. CONNECTION Connection and usage is quite straight forward (it is useful to have the relevant ...

Page 7

LCD DISPLAY SYSTEM SETTINGS NOTE: By way of explanation the following refers to a set of sample buttons that may be obtained as an option. In addition to power on/off and connection for backlight brightness the controller provides an On ...

Page 8

OSD functions Picture : Volume Brightness Contrast Saturation Hue ** Sharpness* Position Backlight Aspect / Size 4 Blue Only ### Increase/decrease volume level, total: 100 steps Increase/decrease panel brightness level, total: 100 steps Increase/decrease panel contrast level, total: 100 steps ...

Page 9

Input : Select the input video signal HD/SD SDI 1 HD/SD SDI 2*** # VGA DVI HD Component Composite 1 Composite 2*** S-Video SD Component # : Press “-“ key to activate the “Auto Picture Setup” function. PIP Setup4 PIP ...

Page 10

Composite 2 S-Video SD Component The corresponding input port name display on OSD menu will disappear once setting “OFF”. De-interlacing Mode* 4 AFM TNR MADI LADI [See Appendix VI for AFM, TNR, MADI, LADI function description] Auto Power : OFF ...

Page 11

G Gain : B Gain : Reset to Defaults : Resume to the default values Reset All to Defaults : Resume all color temperature settings to the default values. Hot Key 4 ### Hot key 1 : Volume / Brightness ...

Page 12

CONNECTORS, PINOUTS & JUMPERS The various connectors are: Summary: Connectors Ref Purpose CN1 Reserved CN2 Panel signal for TTL panel CN3 Panel signal for TTL panel CN4 Panel signal for TTL panel CN6 HD-Component input connector CN7 Audio board connector ...

Page 13

LED1 Dual color LED connector P1 VGA analog input P2 DVI-D or HD-Component input PP2/PP3 Power input (alternative) PP4 External panel power input PP5 Power input S1 LVDS / TTL panel selection S2 LVDS / TTL panel selection SW3 Panel ...

Page 14

Summary: Jumpers setting Ref Purpose JA1 On board +5V logic power enable JA2 On board +3.3V logic power enable JA3 Panel power voltage select CAUTION: Incorrect setting can damage panel JA5 Panel power voltage select CAUTION: Incorrect setting will cause ...

Page 15

Table 1 : Panel voltage setting table : Input voltage via PP2/PP3, PP5 Panel Voltage 3.3V 5V 12VDC 12V CAUTION: Incorrect setting can damage panel & controller Input voltage via PP2/PP3, PP5 Panel Voltage 3.3V 5V 24VDC** 12V 18V CAUTION: ...

Page 16

Input voltage via PP4 Panel Voltage 3. 18VDC* 12V 18V * Maximum current for 3.3V 7A, Maximum current for 12V = 5A, Maximum current for 18V = 3.5A JA3 JA5 JA6 ...

Page 17

JA3, JA5 & JA6 location on board : (Please pay attention to the jumper settings on JA3, JA5 & JA6 which are red in color) ! JA6 & JA5 ! 17 JA3 ...

Page 18

Table 2 : DIP Switch selection – SW3 Pos #1 Pos #2 Pos #3 Pos.#4 OFF ON ON OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF ON OFF OFF ON ON OFF OFF OFF ...

Page 19

CN2 – Panel connector: HIROSE DG20G-40DP-1V (Matching type : DF20A-40DS-1C) PIN SYMBOL 1 GND 2 GND ER0 6 ER1 7 ER2 8 ER3 9 ER4 10 ER5 11 ER6 12 ER7 13 GND 14 GND ...

Page 20

NC 29 OB0 30 OB1 31 OB2 32 OB3 33 OB4 34 OB5 35 OB6 36 OB7 37 GND 38 GND CLK PWR 44 VLCD 45 VLCD 46 VLCD 47 NC ...

Page 21

CN8 – RS-232 serial control: JST B6B-XH-A (Matching type : XHP-6) PIN SYMBOL 1 SDATA 2 SCLK 3 VCC 4 TXD 5 GND 6 RXD CN9 – Ambient light sensor connector : JST B3B-PH-K (Matching type : XHP-3) PIN SYMBOL ...

Page 22

CNV5 – Auxiliary Video input connector, DIL socket header 13x2 PIN IR1 – Infra-Red ...

Page 23

VDD (3,3V/5V) 36 VDD (3,3V/5V VDD +12V / +18V 39 VDD +12V / +18V 40 VDD +12V / +18V LED1 – Status LED connector: 3-pin header PIN Analog VGA in - ...

Page 24

PP4 – External panel power input PIN PP5 - 12V/24VDC power supply PIN 1 2 DESCRIPTION External panel power Ground External panel power Ground DESCRIPTION +12V / +24VDC Ground 24 ...

Page 25

CONTROLLER DIMENSIONS Ready-made 3D Pro-E (SLDPRT) drawing files - Save time and effort for your system volumetric analysis design. Includes jpg file previews. Please go to download at The maximum thickness of the controller is 20.6mm with or without video ...

Page 26

APPLICATION NOTES USING THE CONTROLLER WITHOUT BUTTONS ATTACHED This is very straightforward: • Firstly setup the controller/display system with the buttons. With controls attached and display system active make any settings for colour, tint and image position as required then ...

Page 27

Design Guideline for making VR circuitry : CNB1 – Backlight inverter connector: JST B5B-XH-A (Matching type : XHP-5) PIN SYMBOL 1 GND 2 VBKL 3 BLCTRL 4 BVR_WIP 5 BVR_A CNC1 – Control switch, JST B12B-XH-A (Matching type : XHP-12) ...

Page 28

TROUBLESHOOTING General A general guide to troubleshooting a flat panel display system it is worth considering the system as separate elements, such as: Controller (jumpers, PC settings) Panel (controller, cabling, connection, panel, PC settings) Backlight (inverter, cabling, backlight tubes) Cabling ...

Page 29

SPECIFICATIONS Panel compatibility No. of colours Panel power Panel signal Vertical refresh rate Display clock maximum ADC clock maximum DVI differential input clock maximum Graphics formats Graphics auto mode detect Standard input at source (analog RGB) Video formats Video inputs ...

Page 30

APPENDIX I – SIGNAL SUPPORT MODE TABLE ARGB (P1) PORT : Mode Resolution T_70 720x400 70Hz T_70 720x400 70Hz V_60 640x480 60Hz V_60 640x480 60Hz V_60 640x480 60Hz V_72 640x480 72Hz V_72 640x480 72Hz V_72 640x480 72Hz V_75 640x480 75Hz ...

Page 31

X_60 1024x768 60Hz X_70 1024x768 70Hz X_70 1024x768 70Hz X_70 1024x768 70Hz X_75 1024x768 75Hz X_75 1024x768 75Hz X_75 1024x768 75Hz SX_60 1280x1024 60Hz SX_60 1280x1024 60Hz SX_60 1280x1024 60Hz SX_75 1280x1024 75Hz SX_75 1280x1024 75Hz SX_75 1280x1024 75Hz UX_60 ...

Page 32

HD-COMPONENT (CN6) PORT : Mode Resolution Horizontal freq [KHz] NTSC 720x480i 15.7 PAL 720x576i 15.6 480p/60 720x483 31.469 576p/50 720x576 31.250 720p/60 1280x720 45.000 720p/23.89 1280x720 17.900 720p/24 1280x720 17.900 720p/25 1280x720 18.400 720p/29.97 1280x720 22.500 720p/30 1280x720 22.500 1035i/30 ...

Page 33

Appendix II – RS-232 control protocols RS-232 Serial control (Baud rate 2400, Physical connection : Controller side Connector interface : CN8 Mating connector : JST XHP Mating face of CN8 PIN# Description 4 RS-232 Tx ...

Page 34

Commands to implement switch mount control buttons Function Command Menu button 0xf7 Select-down 0xfa button Select-up button 0xfb Right/+ button 0xfc Left/- button 0xfd 2. Parameter setting - immediate, relative, reset and query Function Command Volume control - 0x80, ...

Page 35

Set display 0x8e, orientation n | “r” | “R” | “?” OSD H position 0x90, nnn | “+” | “-” | “r” | “R” | “?” OSD V position 0x91, nnn | “+” | “-” | “r” | “R” | ...

Page 36

Video System 0x9b, (Composite, S- “0” | “1” | “2” | “3” | video and “r” | “R” | Component Only) “S” | “s”| “?” GAMMA value 0x9d, select n | “r” | “R” “?” Auto power off 0x9f, “0” ...

Page 37

PIP H position 0xa4, nnn | “+” | “-” | “r” | “R” | “?” PIP V position 0xa5, nnn | “+” | “-” | “r” | “R” | “?” PIP window size 0xa6, select ...

Page 38

Vertical Pan 0xb2, nnn | “+” | “-” | “r” | “R” | “?” Colour 0xb3, temperature select n | “r” | “R” | “?” Red level for 0xb4, selected colour temperature nn | “+” | “-” | “r” | ...

Page 39

Set gamma data 0xbf, mm, c, “?” for user defined gamma curve 0xbf, “R” | “r” 0xbf, mm Backlight control 0xe0 “+” | “-” | “R” | “r” | “?” Backlight On/Off 0xe1, “0” | “1” ...

Page 40

Backlight Invert 0xe7 “0” | “1” | “R” | “r” ”?” Red Offset for 0xe8, selected colour temperature nn | “+” | “-” | “r” | “R” | “?” Green Offset for 0xe9, selected colour temperature nn | “+” | ...

Page 41

Video de-interlace 0xca, method “0” | “1” “r” | “R” “?” Query BIOS 0xcb, “0” version Query PCBA 0xcb, “1” number Reset parameter 0xce Wide Screen 0xd9, Mode Selection “0” | “1”| “2” “r” | “R” “?” “E”,”2” HDSDI2 “F”,”1” ...

Page 42

The following commands for sending texts by using RS-232 command. Function Command Send Line 0xF0, |”S” |”LL”|”TEXT”| “0x0A” Return “1” e.g Display “Send Text” message on screen: RS232 Code:“0xF0 0x53 0x30 0x31 0x53 0x65 0x6E 0x64 0x20 0x54 0x65 0x78 ...

Page 43

Set background Transparency value is 8 RS232 Code: “0xF0 0x42 0x38” Return Code: “0xF0 0x42 0x38 0x38” * Note : Please set the "Background Transparency” and "Left offset" commands before the "Send Line" command 1-byte ascii-coded hex number, ...

Page 44

Hex to ASCII conversion table Hex ASCII Hex 0x30 0 0x41 0x31 1 0x42 0x32 2 0x43 0x33 3 0x44 0x34 4 0x45 0x35 5 0x46 0x36 6 0x47 0x37 7 0x48 0x38 8 0x49 0x39 9 0x4A 0x4B 0x4C ...

Page 45

Appendix III – Mapping definition • Definition of Mapping ...

Page 46

Definition of Mapping ...

Page 47

Appendix IV – Auto Color Gain The Auto Color Gain function is supported in the ARGB mode only and is designed to calibrate the controller to the incoming video signal. In order to calibrate correctly, the display must be displaying ...

Page 48

Appendix V – DV remote control unit work for SVH-1920 P/N 559000106-3 : DigitalView remote control unit (without DV logo silk screen printing) P/N 559000105-3 : DigitalView remote control unit (with DigitalView logo silk screen printing) BUTTON POWER BUTTON Soft ...

Page 49

Appendix VI – Function description for de-interlacing mode AFM, TNR, MADI, LADI AFM = Auto Film Mode : frame based method which used for the input ODD and EVEN fields have a fixed relation between each other, ...

Page 50

... LIMITATION OF LIABILITY The manufacturer’s liability for damages to customer or others resulting from the use of any product supplied hereunder shall in no event exceed the purchase price of said product. TRADEMARKS The following are trademarks of Digital View Ltd: • Digital View • SVH-1920 ...

Page 51

... CONTACT DETAILS Digital View has offices in Asia, Europe and USA : ASIA Digital View Ltd 16 th Floor Millennium City 3 370 Kwun Tong Road Kwun Tong Hong Kong Tel: (852) 2861 3615 hksales@digitalview.com Sales: EUROPE Digital View Ltd. 6 Marylebone Passage, London, W1W 8EX, UK ...

Page 52

Inverter Interface Board P/N 416040010-3 [OPERATE UNDER 12VDC POWER INPUT ENVIRONMENT] The Inverter interface board provides interface to drive up the high current consumption panel inverter in excess of 3.5A. This board enables current Amps to ...

Page 53

Illustrated Diagram PP1 - 12VDC power supply – input, Power header 4 ways 0.156” pitch PIN PP2 – Alternate 12VDC power supply – input, Terminal Block 2 poles PIN PP3 – 12VDC ...

Page 54

CNB3 – Inverter interface to backlight inverter, JST B8B-XH-A PIN SYMBOL 1 VLCD12 2 VLCD12 3 GND 4 GND 5 VLCD12 6 BLCTRL 7 BVR_WIP 8 BVR_A DESCRIPTION Panel power Panel power Ground Ground Panel power Backlight on/off control signal ...

Page 55

Audio Add-on Board P/N 416940020-3 [OPERATE UNDER 12VDC POWER INPUT ENVIRONMENT] The Audio add-on board P/N 416940020-3 design for connection with DV controllers on the audio connector CN7. It provides audio input ports and output port for sound amplification. Electrical ...

Page 56

CN3 : Controller interface connector Pin Number 1 +5V 2 Left trimpot chip select 3 Right trimpot chip select 4 Trimpot serial data 5 Trimpot serial clock 6 Digital Ground 7 +12V 8 Audio input left 9 Audio input right ...