93AA86/P Microchip Technology, 93AA86/P Datasheet - Page 6

• Manufacturer Part Number: 93AA86/P
• Description: IC EEPROM 16KBIT 3MHZ 8DIP
• Manufacturer: Microchip Technology

Specifications of 93AA86/P

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 16K (2K x 8 or 1K x 16)
• Speed: 1MHz, 2MHz, 3MHz
• Interface: Microwire, 3-Wire Serial
• Voltage - Supply: 1.8 V ~ 6 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

93AA76/86
2.0
When the ORG pin is connected to V
organization is selected. When it is connected to ground,
the x8 organization is selected. Instructions, addresses
and write data are clocked into the DI pin on the rising
edge of the clock (CLK). The DO pin is normally held in
a high-Z state except when reading data from the
device, or when checking the Ready/Busy status during
a programming operation. The Ready/Busy status can
be verified during an erase/write operation by polling the
DO pin; DO low indicates that programming is still in
progress, while DO high indicates the device is ready.
The DO will enter the high-impedance state on the falling
edge of the CS.
2.1
The Start bit is detected by the device if CS and DI are
both high with respect to the positive edge of CLK for
the first time.
Before a Start condition is detected, CS, CLK and DI
may change in any combination (except to that of a
Start condition), without resulting in any device opera-
tion (Read, Write, Erase, EWEN, EWDS, ERAL and
WRAL). As soon as CS is high, the device is no longer
in the Standby mode.
An instruction following a Start condition will only be
executed if the required amount of opcode, address
and data bits for any particular instruction are clocked
in.
After execution of an instruction (i.e., clock in or out of
the last required address or data bit) CLK and DI
become “don't care” bits until a new Start condition is
detected.
2.2
It is possible to connect the Data In and Data Out pins
together. However, with this configuration it is possible
for a “bus conflict” to occur during the “dummy zero”
that precedes the read operation, if A0 is a logic high
level. Under such a condition the voltage level seen at
Data Out is undefined and will depend upon the relative
impedances of Data Out and the signal source driving
A0. The higher the current sourcing capability of A0,
the higher the voltage at the Data Out pin.
DS21130E-page 6
PRINCIPLES OF OPERATION
Start Condition
DI/DO
CC
, the x16
2.3
The 93AA76/86 powers up in the Erase/Write Disable
(EWDS) state. All programming modes must be
preceded by an Erase/Write Enable (EWEN) instruction.
Once the EWEN instruction is executed, programming
remains enabled until an EWDS instruction is executed
or V
accidental data disturb, the EWDS instruction can be
used to disable all erase/write functions and should
follow all programming operations. Execution of a READ
instruction is independent of both the EWEN and EWDS
instructions.
2.4
During power-up, all programming modes of operation
are inhibited until V
1.4V. During power-down, the source data protection
circuitry acts to inhibit all programming modes when
V
The EWEN and EWDS commands give additional
protection against accidentally programming during
normal operation.
After power-up, the device is automatically in the
EWDS mode. Therefore, an EWEN instruction must be
performed before any ERASE or WRITE instruction can
be executed.
CC
CC
has fallen below 1.4V.
is removed from the device. To protect against
Erase/Write Enable and Disable
(EWEN, EWDS)
Data Protection
CC
has reached a level greater than
 2004 Microchip Technology Inc.