25AA160/P Microchip Technology, 25AA160/P Datasheet
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
25AA160/P
Specifications of 25AA160/P
Available stocks
Related parts for 25AA160/P
25AA160/P Summary of contents
Page 1
... Microchip Technology Inc. Not recommended for new designs – Please use 25AA160A/B or 25LC160A/B. 25AA160/25LC160/25C160 ™ Bus Serial EEPROM Description: The Microchip Technology Inc. 25AA160/25LC160/ Temp 25C160 (25XX160 Ranges Erasable PROMs. The memory is accessed via a I simple Serial Peripheral Interface™ (SPI™) compati- ble serial bus ...
Page 2
... CC Conditions 2.7V (Note) < 2.7V (Note) 2.7V (Note) < 2.7V (Note 1.0 mA, V < 2. -400 OUT 5.0V (Note) = 5.5V 3.0 MHz; CLK = 2.5V 2.0 MHz; CLK = 5.5V = 2.5V = 5.5V, Inputs tied 2.5V, Inputs tied 2004 Microchip Technology Inc. ...
Page 3
... Endurance Note 1: This parameter is periodically sampled and not 100% tested. 2: This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please ™ consult the Total Endurance 2004 Microchip Technology Inc. 25AA160/25LC160/25C160 Industrial (I -40°C to +85°C A ...
Page 4
... SERIAL INPUT TIMING CS 2 Mode 1,1 SCK Mode 0 MSB in SO FIGURE 1-3: SERIAL OUTPUT TIMING SCK 13 MSB out SO SI DS21231D-page High-impedance n don’t care High-impedance 14 don’t care LSB in 3 Mode 1,1 Mode 0,0 15 ISB out 2004 Microchip Technology Inc. ...
Page 5
... AC Test Conditions AC Waveform 0. 0. 4.0V HI Timing Measurement Reference Level Input Output Note 1: For V 4. For V > 4.0V CC 2004 Microchip Technology Inc. 25AA160/25LC160/25C160 FIGURE 1-4: — (Note 1) (Note TEST CIRCUIT V CC 2.25 K 100 pF 1.8 K DS21231D-page 5 ...
Page 6
... To resume serial communication, HOLD must be brought high while the SCK pin is low, otherwise serial commu- nication will not resume. Lowering the HOLD line at any time will tri-state the SO line. 2004 Microchip Technology Inc. ...
Page 7
... WREN 0000 0101 RDSR 0000 0001 WRSR 2004 Microchip Technology Inc. 25AA160/25LC160/25C160 3.3 Write Sequence Prior to any attempt to write data to the 25XX160, the write enable latch must be set by issuing the WREN instruction (Figure 3-4). This is done by setting CS low and then clocking out the proper instruction into the 25XX160 ...
Page 8
... BYTE WRITE SEQUENCE SCK instruction High-impedance SO FIGURE 3-3: PAGE WRITE SEQUENCE SCK instruction SCK data byte DS21231D-page 16-bit address 16-bit address 16-bit address data byte data out Twc data byte data byte data byte n (16 max 2004 Microchip Technology Inc. ...
Page 9
... SO FIGURE 3-5: WRITE DISABLE SEQUENCE CS SCK SI SO 2004 Microchip Technology Inc. 25AA160/25LC160/25C160 The following is a list of conditions under which the write enable latch will be reset: • Power-up • WRDI instruction successfully executed • WRSR instruction successfully executed • WRITE instruction successfully executed ...
Page 10
... See Figure 3-6 for the RDSR timing sequence data from Status register TABLE 3-2: BP1 ’, the latch 0 ’, the latch ARRAY PROTECTION Array Addresses BP0 Write-Protected 0 none 1 upper 1/4 (0600h - 07FFh) 0 upper 1/2 (0400h - 07FFh) 1 all (0000h - 07FFh) 2004 Microchip Technology Inc. ...
Page 11
... Access to the array during an internal write cycle is ignored and programming is continued TABLE 3-3: WRITE-PROTECT FUNCTIONALITY MATRIX WPEN WP WEL Low 1 1 High X 1 2004 Microchip Technology Inc. 25AA160/25LC160/25C160 data to Status register High-impedance 3.8 Power On State The 25XX160 powers on in the following state: • ...
Page 12
... For PICmicro device marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price. DS21231D-page 12 Example: 25LC160 I/PNNN YYWW Example: 25C160 I/SNYYWW NNN 2004 Microchip Technology Inc. ...
Page 13
... Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-001 Drawing No. C04-018 2004 Microchip Technology Inc. 25AA160/25LC160/25C160 ...
Page 14
... A2 MILLIMETERS MIN NOM MAX 8 1.27 1.35 1.55 1.75 1.32 1.42 1.55 0.10 0.18 0.25 5.79 6.02 6.20 3.71 3.91 3.99 4.80 4.90 5.00 0.25 0.38 0.51 0.48 0.62 0. 0.20 0.23 0.25 0.33 0.42 0. 2004 Microchip Technology Inc. ...
Page 15
... APPENDIX A: REVISION HISTORY Revision D Added note to page 1 header (Not recommended for new designs). Updated document format. 2004 Microchip Technology Inc. 25AA160/25LC160/25C160 DS21231D-page 15 ...
Page 16
... NOTES: DS21231D-page 16 2004 Microchip Technology Inc. ...
Page 17
... Links to other useful web sites related to Microchip Products • Conferences for products, Development Systems, technical information and more • Listing of seminars and events 2004 Microchip Technology Inc. 25AA160/25LC160/25C160 SYSTEMS INFORMATION AND UPGRADE HOT LINE The Systems Information and Upgrade Line provides system users a listing of the latest versions of all of Microchip's development systems software products ...
Page 18
... What deletions from the document could be made without affecting the overall usefulness there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS21231D-page 18 Total Pages Sent ________ FAX: (______) _________ - _________ N Literature Number: DS21231D 2004 Microchip Technology Inc. ...
Page 19
... The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. 2004 Microchip Technology Inc. 25AA160/25LC160/25C160 XXX Examples: ...
Page 20
... NOTES: DS21231D-page 20 2004 Microchip Technology Inc. ...
Page 21
... PICLAB, PICtail, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 22
... Via Salvatore Quasimodo, 12 20025 Legnano (MI) Milan, Italy Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands Waegenburghtplein 4 NL-5152 JR, Drunen, Netherlands Tel: 31-416-690399 Fax: 31-416-690340 United Kingdom 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44-118-921-5869 Fax: 44-118-921-5820 07/12/04 2004 Microchip Technology Inc. ...