24LC22A-I/SN Microchip Technology, 24LC22A-I/SN Datasheet - Page 13

no-image

24LC22A-I/SN

Manufacturer Part Number
24LC22A-I/SN
Description
IC EEPROM 2KBIT 400KHZ 8SOIC
Manufacturer
Microchip Technology
Datasheets

Specifications of 24LC22A-I/SN

Memory Size
2K (256 x 8)
Package / Case
8-SOIC (3.9mm Width)
Operating Temperature
-40°C ~ 85°C
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
100kHz, 400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.5 V ~ 5.5 V
Organization
256 K x 8
Interface Type
2-Wire
Maximum Clock Frequency
0.1 MHz
Access Time
10 ms
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.5 V
Maximum Operating Current
3 mA
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
2.5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
24LC22A-I/SNG
24LC22A-I/SNG
24LC22AI/SN

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
24LC22A-I/SN
Manufacturer:
MICR
Quantity:
20 000
FIGURE 7-3:
8.0
The descriptions of the pins are listed in Table 8-1.
TABLE 8-1:
8.1
This pin is used to transfer addresses and data into and
out of the device, when the device is in the Bidirectional
mode. In the Transmit-Only mode, which only allows
data to be read from the device, data is also transferred
on the SDA pin. This pin is an open drain terminal,
therefore the SDA bus requires a pull-up resistor to
V
For normal data transfer in the Bidirectional mode, SDA
is allowed to change only during SCL low. Changes
during SCL high are reserved for indicating the Start
and Stop conditions.
© 2007 Microchip Technology Inc.
CC
Bus Activity
Master
SDA Line
Bus Activity
(typical 10 kΩ for 100 kHz, 2 kΩ for 400 kHz).
Name
VCLK
SDA
SCL
V
V
NC
CC
SS
PIN DESCRIPTIONS
Serial Address/Data Input/Output
(SDA)
Control
Byte
PIN FUNCTION TABLE
Ground
Serial Address/Data I/O
Serial Clock (Bidirectional mode)
Serial Clock (Transmit-Only mode)
+2.5V to 5.5V Power Supply
No Internal Connection
A
C
K
SEQUENTIAL READ
Data n
Function
A
C
K
Data n + 1
C
A
K
8.2
This pin is the clock input for the Bidirectional mode,
and is used to synchronize data transfer to and from the
device. It is also used as the signaling input to switch
the device from the Transmit-Only mode to the Bidirec-
tional mode. It must remain high for the chip to continue
operation in the Transmit-Only mode.
8.3
This pin is the clock input for the Transmit-Only mode
(DDC1). In the Transmit-Only mode, each bit is clocked
out on the rising edge of this signal. In the Bidirectional
mode, a high logic level is required on this pin to enable
write capability.
Data n + 2
Serial Clock (SCL)
Serial Clock (VCLK)
A
C
K
24LC22A
Data n + x
DS21683B-page 13
O
N
A
C
K
S
T
O
P
P

Related parts for 24LC22A-I/SN