MAX6726AKATED4+T Maxim Integrated, MAX6726AKATED4+T Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
MAX6726AKATED4+T
Manufacturer Part Number
MAX6726AKATED4+T
Description
Supervisory Circuits
Manufacturer
Maxim Integrated
Series
MAX6715A, MAX6716A, MAX6717A, MAX6718A, MAX6719A, MAX6720A, MAX6721A, MAX6722A, MAX6723A, MAX6724A, MAX6725A, MAX6726A, MAX6727A, MAX6728A, MAX6729A, MAX6797Ar
Datasheet
1.MAX1180ECMTD.pdf
(18 pages)
Specifications of MAX6726AKATED4+T
Number Of Voltages Monitored
3
Monitored Voltage
1.8 V to 5 V, 0.9 V to 3.3 V
Undervoltage Threshold
3 V, 0.81 V, Adjustable
Overvoltage Threshold
3.15 V, 0.855 V, Adjustable
Output Type
Active High, Active Low, Push-Pull
Manual Reset
Resettable
Watchdog
Watchdog
Battery Backup Switching
No Backup
Power-up Reset Delay (typ)
2240 ms
Supply Voltage - Max
5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Package / Case
SOT-23
Chip Enable Signals
No
Maximum Power Dissipation
714 mW
Minimum Operating Temperature
- 40 C
Power Fail Detection
No
Supply Current (typ)
15 uA
Supply Voltage - Min
0.8 V
The MAX6715A–MAX6729A/MAX6797A µP supervisory
circuits maintain system integrity by alerting the µP to
fault conditions. These ICs are optimized for systems
that monitor two or three supply voltages. The output-
reset state is guaranteed to remain valid while either
V
Input-voltage threshold level combinations are indicat-
ed by a two-letter code in the Reset Voltage Threshold
Suffix Guide (Table 1). Contact factory for availability of
other voltage threshold combinations.
The MAX6715A–MAX6729A/MAX6797A provide an
active-low reset output (RST) and the MAX6725A/
MAX6726A also provide an active-high (RST) output.
RST, RST, RST1, and RST2 are asserted when the volt-
age at either V
threshold level, RSTIN drops below threshold, or MR is
pulled low. Once reset is asserted, it stays low for the
reset timeout period (see Table 2). If V
RSTIN goes below the reset threshold before the reset
timeout period is completed, the internal timer restarts.
The MAX6715A/MAX6717A/MAX6719A/MAX6721A/
MAX6723A/MAX6725A/MAX6727A/MAX6728A contain
open-drain reset outputs, while the MAX6716A/
M A X 6 7 1 8 A / M A X 6 7 2 0 A / M A X 6 7 2 2 A / M A X 6 7 2 4 A /
MAX6726A/MAX6729A/MAX6797A contain push-pull
reset outputs. The MAX6727A provides two separate
open-drain RST outputs driven by the same internal logic.
Many µP-based products require manual-reset capabil-
ity, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. A logic-low on MR
asserts the reset output. Reset remains asserted while
MR is low for the reset timeout period (t
returns high. This input has an internal 50kΩ pullup
resistor to V
used. MR can be driven with CMOS logic levels, or with
open-drain/collector outputs. Connect a normally open
momentary switch from MR to GND to create a manual-
reset function; external debounce circuitry is not
required. If MR is driven from long cables or if the
device is used in a noisy environment, connect a 0.1µF
capacitor from MR to GND to provide additional noise
immunity.
Dual/Triple, Ultra-Low-Voltage, SOT23 µP
Supervisory Circuits
10
CC
1 or V
______________________________________________________________________________________
CC
2 is above 0.8V.
CC
1 and can be left unconnected if not
CC
1 or V
Detailed Description
CC
2 falls below the voltage
Manual-Reset Input
Threshold Levels
Supply Voltages
Reset Outputs
CC
RP
1, V
) after MR
CC
2, or
The MAX6719A/MAX6720A and MAX6723A–MAX6727A
provide an additional input to monitor a third system volt-
age. The threshold voltage at RSTIN is typically 626mV.
Connect a resistor-divider network to the circuit as shown
in Figure 1 to establish an externally controlled threshold
voltage, V
Low-leakage current at RSTIN allows the use of large-
valued resistors resulting in reduced power consump-
tion of the system.
The watchdog monitors µP activity through the watch-
dog input (WDI). To use the watchdog function, con-
nect WDI to a bus line or µP I/O line. When WDI
remains high or low for longer than the watchdog time-
out period, the reset output asserts.
The MAX6721A–MAX6729A/MAX6797A include a dual-
mode watchdog timer to monitor µP activity. The flexi-
ble timeout architecture provides a long period initial
watchdog mode, allowing complicated systems to
complete lengthy boots, and a short period normal
watchdog mode, allowing the supervisor to provide
quick alerts when processor activity fails. After each
reset event (V
watchdog reset), there is a long initial watchdog period
of 35s minimum. The long watchdog period mode pro-
vides an extended time for the system to power-up and
fully initialize all µP and system components before
assuming responsibility for routine watchdog updates.
Figure 1. Monitoring a Third Voltage
V
EXT_TH
EXT_TH
V
EXT_TH
CC
.
R1
R2
power-up/brownout, manual reset, or
= 626mV((R1 + R2)/R2)
RSTIN
Adjustable Input Voltage
MAX6723A–
MAX6719A/
MAX6720A/
MAX6727A
GND
Watchdog Input