MAX6888FETE Maxim Integrated, MAX6888FETE Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
MAX6888FETE
Manufacturer Part Number
MAX6888FETE
Description
Supervisory Circuits
Manufacturer
Maxim Integrated
Series
MAX6887, MAX6888r
Datasheet
1.MAX6887RETE.pdf
(13 pages)
Specifications of MAX6888FETE
Number Of Voltages Monitored
4
Undervoltage Threshold
3.06 V, 2.31 V, 1.39 V, 0.557 V
Overvoltage Threshold
3.54 V, 2.68 V, 1.61 V, 0.643 V
Manual Reset
Resettable
Watchdog
Watchdog
Supply Voltage - Max
5.8 V
Maximum Operating Temperature
+ 85 C
Package / Case
TQFN EP
Maximum Power Dissipation
1667 mW
Minimum Operating Temperature
- 40 C
Supply Current (typ)
900 uA
Supply Voltage - Min
2.7 V
The MAX6887/MAX6888 provide several supply-detector
inputs, one watchdog input, and three outputs for power-
supply monitoring applications. The MAX6887 offers six
voltage-detector inputs, while the MAX6888 offers four.
Each voltage-detector input offers both an undervoltage
and overvoltage threshold.
The undervoltage and overvoltage thresholds are facto-
ry-set for monitoring standard supply voltages (see the
Selector Guide ). Inputs in the Selector Guide that con-
tain “Adj” allow an external voltage-divider to be con-
nected to set a user-defined threshold.
RESET goes low when any input voltage drops below
its undervoltage threshold or when MR is brought low.
RESET stays low for 200ms after all assertion-causing
conditions have been cleared. OV goes low when an
input voltage rises above its overvoltage threshold. OV
typically stays low for 25µs (typ) after all inputs fall
back under their overvoltage thresholds.
The MAX6887/MAX6888 offer a watchdog timer with
initial and normal timeout periods of 102.4s and 1.6s,
respectively. WDO goes low when the watchdog timer
expires and deasserts when WDI transitions from low-
to-high or high-to-low.
The MAX6887/MAX6888 derive power from the voltage-
detector inputs IN1–IN4 or through an externally sup-
plied V
positive input that supplies power to the device (see
the Functional Diagram ). The highest input voltage on
IN1–IN4 supplies power to the device. One of IN1–IN4
must be at least 2.7V to ensure proper operation.
Internal hysteresis ensures that the supply input that
initially powered the device continues to power the
device when multiple input voltages are within 50mV of
each other.
V
nection for the MAX6887/MAX6888 internal supply.
Bypass V
installed as close to the device as possible. The inter-
nal supply voltage, measured at V
mum of IN1–IN4. If V
must be at least 200mV higher than any voltage
applied to IN1–IN4 and V
V
set as “Adj.” Do not use the internally generated V
provide power to external circuitry.
CC
CC
powers the analog circuitry and is the bypass con-
always powers the device when all IN_ are factory
Hex/Quad, Power-Supply Supervisory Circuits
CC
. A virtual diode-ORing scheme selects the
CC
Powering the MAX6887/MAX6888
to GND with a 1µF ceramic capacitor
_______________________________________________________________________________________
Detailed Description
CC
CC
is externally supplied, V
must be brought up first.
CC
, equals the maxi-
CC
CC
to
The MAX6887/MAX6888 generate a supply voltage at
BP for the internal logic circuitry. Bypass BP to GND with
a 1µF ceramic capacitor installed as close to the device
as possible. The nominal BP output voltage is +2.55V.
Do not use BP to provide power to external circuitry.
The MAX6887 offers six voltage-detector inputs, while
the MAX6888 offers four voltage-detector inputs. Each
voltage-detector input offers an undervoltage and over-
voltage threshold set at the factory to monitor standard
supply voltages (see the Selector Guide ). The 5% and
10% tolerances are based on maximum and minimum
threshold values. Actual thresholds for the
MAX6887/MAX6888 are shown in Tables 1 and 2.
Inputs in the Selector Guide listing “Adj” allow an exter-
nal voltage-divider to be connected to set a user-
defined threshold.
Inputs listed in the Selector Guide containing “Adj” for
inputs allow external resistor voltage-dividers to be
connected at the voltage-detector inputs. These inputs
monitor any voltage supply higher than 0.6V (see
Figure 1). Use the following equation to set a voltage-
Figure 1. Adjusting the Monitored Threshold
*V
TO 0.6V ACCORDING TO THE DEVICE'S TOLERANCE
R1
R2
REFOV
V
IN
AND V
IN_
REFUV
ARE REFERENCED
*V
*V
REFUV
REFOV
Adjustable Threshold Inputs
MAX6887
MAX6888
Inputs
7