M95010-WDW6TP STMicroelectronics, M95010-WDW6TP Datasheet - Page 20

• Manufacturer Part Number: M95010-WDW6TP
• Description: IC EEPROM 1KBIT 10MHZ 8TSSOP
• Manufacturer: STMicroelectronics

Specifications of M95010-WDW6TP

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 1K (128 x 8)
• Speed: 10MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-TSSOP
• Density: 1Kb
• Interface Type: Serial (SPI)
• Organization: 128x8
• Access Time (max): 35ns
• Frequency (max): 10MHz
• Write Protection: Yes
• Data Retention: 40Year
• Operating Supply Voltage (typ): 3.3/5V
• Package Type: TSSOP
• Operating Temp Range: -40C to 85C
• Supply Current: 2mA
• Operating Supply Voltage (min): 2.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Maximum Clock Frequency: 5 MHz
• Access Time: 60 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.5 V
• Maximum Operating Current: 2 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 3.3 V, 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-8671-2; M95010-WDW6TP

Instructions
6.4
20/43
Write Status Register (WRSR)
The Write Status Register (WRSR) instruction allows new values to be written to the Status
register. Before it can be accepted, a Write Enable (WREN) instruction must previously have
been executed.
The Write Status Register (WRSR) instruction is entered by driving Chip Select (S) low,
sending the instruction code followed by the data byte on Serial Data input (D), and driving
the Chip Select (S) signal high. Chip Select (S) must be driven high after the rising edge of
Serial Clock (C) that latches in the eighth bit of the data byte, and before the next rising edge
of Serial Clock (C). Otherwise, the Write Status Register (WRSR) instruction is not
executed.
Driving the Chip Select (S) signal high at a byte boundary of the input data triggers the self-
timed write cycle that takes t
instruction sequence is shown in
While the Write Status Register cycle is in progress, the Status register may still be read to
check the value of the Write in progress (WIP) bit: the WIP bit is 1 during the self-timed write
cycle t
reset at the end of the write cycle t
The Write Status Register (WRSR) instruction allows the user to change the values of the
BP1, BP0 bits which define the size of the area that is to be treated as read only, as defined
in
The contents of the BP1, BP0 bits are updated after the completion of the WRSR
instruction, including the t
The Write Status Register (WRSR) instruction has no effect on the b7, b6, b5, b4, b1 and b0
bits in the Status register. Bits b7, b6, b5, b4 are always read as 0.
Figure 10. Write Status Register (WRSR) sequence
The instruction is not accepted, and is not executed, under the following conditions:
●
●
●
●
Table
if the Write Enable Latch (WEL) bit has not been set to 1 (by executing a Write Enable
instruction just before)
if a write cycle is already in progress
if the device has not been deselected, by Chip Select (S) being driven high, after the
eighth bit, b0, of the data byte has been latched in
if Write Protect (W) is low during the WRSR command (instruction, address and data)
W
, and, 0 when the write cycle is complete. The WEL bit (Write enable latch) is also
3.
S
C
D
Q
0
1
W
High Impedance
write cycle.
2
W
Instruction
to complete (as specified in
Doc ID 6512 Rev 8
3
Figure
4
W
.
5
6
10.
7
MSB
7
8
6
9 10 11 12 13 14 15
5
Register In
4
Status
3
Table 13
2
1
M95040, M95020, M95010
0
to
AI01445B
Table
20). The