MAX13085EAPA Maxim Integrated, MAX13085EAPA Datasheet - Page 18

• Manufacturer Part Number: MAX13085EAPA
• Description: RS-422/RS-485 Interface IC
• Manufacturer: Maxim Integrated

Specifications of MAX13085EAPA

• Data Rate: 500 Kbps
• Operating Supply Voltage: 5 V
• Supply Current: 1.8 mA
• Operating Temperature Range: - 40 C to + 125 C
• Number Of Drivers: 1
• Number Of Receivers: 1
• Product: RS-422/RS-485 Combination

MAX13086E–MAX13089E
18
Low-power shutdown mode is initiated by bringing both
RE high and DE low. In shutdown, the devices typically
draw only 2.8µA of supply current.
RE and DE can be driven simultaneously; the devices
are guaranteed not to enter shutdown if RE is high and
DE is low for less than 50ns. If the inputs are in this
state for at least 700ns, the devices are guaranteed to
enter shutdown.
Enable times t
Characteristics section) assume the devices were not in
a low-power shutdown state. Enable times t
t
takes drivers and receivers longer to become enabled
from low-power shutdown mode (t
than from driver/receiver-disable mode (t
+5.0V, ±15kV ESD-Protected, Fail-Safe,
Hot-Swap, RS-485/RS-422 Transceivers
Figure 11. Line Repeater for MAX13080E/MAX13081E/
MAX13083E/MAX13084E/MAX13086E/MAX13087E/MAX13089E
in Full-Duplex Mode
Figure 12. Typical Half-Duplex RS-485 Network
ZL(SHDN)
RO
RE
DE
DI
RO
DE
RE
MAX13081E/MAX13084E/MAX13087E)
DI
Low-Power Shutdown Mode (Except
MAX13089E (HALF DUPLEX)
assume the devices were in shutdown state. It
D
R
MAX13082E
MAX13088E
D
ZH
R
A
B
Z
Y
MAX13080E/MAX13081E/MAX13083E/
MAX13084E/MAX13086E/MAX13087E/
and t
120Ω
120Ω
MAX13089E (FULL DUPLEX)
ZL
B
A
(see the Switching
120Ω
ZH(SHDN)
ZH
B
DI
ZH(SHDN)
, t
DATA IN
DATA OUT
D
, t
ZL
ZL(SHDN)
).
A
DE
and
RO
R
)
RE
Two mechanisms prevent excessive output current and
power dissipation caused by faults or by bus contention.
The first, a foldback current limit on the output stage,
provides immediate protection against short circuits over
the whole common-mode voltage range (see the Typical
Operating Characteristics ). The second, a thermal-shut-
down circuit, forces the driver outputs into a high-imped-
ance state if the die temperature exceeds +175°C (typ).
The RS-485/RS-422 standard covers line lengths up to
4000ft. For line lengths greater than 4000ft, use the
repeater application shown in Figure 11.
The MAX13082E/MAX13088E/MAX13089E transceivers
are designed for bidirectional data communications on
multipoint bus transmission lines. Figures 12 and 13
show typical network applications circuits.
To minimize reflections, terminate the line at both ends
in its characteristic impedance, and keep stub lengths
off the main line as short as possible. The slew-rate-lim-
ited MAX13082E and the two modes of the MAX13089E
are more tolerant of imperfect termination.
PROCESS: BiCMOS
B
DI
D
A
DE
RO
120Ω
R
RE
Driver Output Protection
B
A
Chip Information
Typical Applications
R
D
Line Length
Maxim Integrated
DE
DI
RO
RE