CAT1024ZI-42-G ON Semiconductor, CAT1024ZI-42-G Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
CAT1024ZI-42-G
Manufacturer Part Number
CAT1024ZI-42-G
Description
Supervisory Circuits CPU w/2K
Manufacturer
ON Semiconductor
Datasheet
1.CAT1024ZI-42-G.pdf
(19 pages)
Specifications of CAT1024ZI-42-G
Product Category
Supervisory Circuits
Rohs
yes
Number Of Voltages Monitored
1
Monitored Voltage
3 V, 3.3 V, 5 V
Undervoltage Threshold
4.25 V
Overvoltage Threshold
4.5 V
Manual Reset
Resettable
Watchdog
No Watchdog
Supply Voltage - Max
5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
MSOP-8
Maximum Power Dissipation
1000 mW
Minimum Operating Temperature
- 40 C
Supply Current (typ)
3000 uA
Supply Voltage - Min
2.7 V
Page Write
write cycle, using the Page Write operation. The page write
operation is initiated in the same manner as the byte write
operation, however instead of terminating after the initial
byte is transmitted, the Master is allowed to send up to 15
additional bytes. After each byte has been transmitted, the
CAT1024/25 will respond with an acknowledge and
internally increment the lower order address bits by one. The
high order bits remain unchanged.
Acknowledge Polling
the typical write cycle time. Once the stop condition is issued
to indicate the end of the host’s write operation, the
CAT1024/25 initiates the internal write cycle. ACK polling
can be initiated immediately. This involves issuing the start
user to protect against inadvertent memory array
programming. If the WP pin is tied to V
memory array is protected and becomes read only. The
the same manner as the write operation with one exception,
the R/W bit is set to one. Three different READ operations
The CAT1024/25 writes up to 16 bytes of data in a single
Disabling of the inputs can be used to take advantage of
The Write Protection feature (CAT1025 only) allows the
The READ operation for the CAT1024/25 is initiated in
BUS ACTIVITY:
SDA LINE
MASTER
S
BUS ACTIVITY:
R
S
T
A
T
SDA LINE
ADDRESS
MASTER
SLAVE
S
S
A
R
T
T
A
C
K
WRITE PROTECTION PIN (WP)
CC
ADDRESS (n)
ADDRESS
Figure 9. Page Write Timing
Figure 8. Byte Write Timing
, the entire
SLAVE
BYTE
READ OPERATIONS
http://onsemi.com
C
A
K
A
C
K
11
ADDRESS
the STOP condition, the address counter ‘wraps around,’
and previously transmitted data will be overwritten.
has been sent by the Master, the internal programming cycle
begins. At this point, all received data is written to the
CAT1024/25 in a single write cycle.
condition followed by the slave address for a write
operation. If the device is still busy with the write operation,
no ACK will be returned. If a write operation has completed,
an ACK will be returned and the host can then proceed with
the next read or write operation.
CAT1025 will accept both slave and byte addresses, but the
memory location accessed is protected from programming
by the device’s failure to send an acknowledge after the first
byte of data is received.
are
Selective/Random READ and Sequential READ.
BYTE
DATA n
If the Master transmits more than 16 bytes before sending
When all 16 bytes are received, and the STOP condition
possible:
A
C
K
A
C
K
DATA n+1
DATA
Immediate/Current
C
A
K
C
A
K
P
O
S
T
P
DATA n+15
Address
C
A
K
O
S
T
P
P
READ,