MAX208EAG+ Maxim Integrated, MAX208EAG+ Datasheet - Page 4

• Manufacturer Part Number: MAX208EAG+
• Description: RS-232 Interface IC
• Manufacturer: Maxim Integrated
• Series: MAX200, MAX201, MAX202, MAX203, MAX204, MAX205, MAX206, MAX207, MAX208, MAX209, MAX211, MAX213r

Specifications of MAX208EAG+

• Data Rate: 120 Kbps
• Operating Supply Voltage: 5 V
• Supply Current: 20 mA
• Operating Temperature Range: 0 C to + 70 C
• Function: Transceiver
• Number Of Drivers: 4
• Number Of I/os: 16
• Number Of Receivers: 4
• Propagation Delay Time Ns: 10 us
• Shutdown: No

AC ELECTRICAL CHARACTERISTICS (continued)
(V
MAX4228, R
1GHz, Low-Power, SOT23,
Current-Feedback Amplifiers with Shutdown
(V
4
__________________________________________Typical Operating Characteristics
Note 1: The MAX422_EUT is 100% production tested at T
Note 2: Absolute Maximum Power Dissipation must be observed.
Note 3: Does not include impedance of external feedback resistor network.
Note 4: AC specifications shown are with optimal values of R
Note 5: The AC specifications shown are not measured in a production test environment. The minimum AC specifications given are
Note 6: Input Test Signal: 3.58MHz sine wave of amplitude 40IRE superimposed on a linear ramp (0IRE to 100IRE). IRE is a unit of
Note 7: Assumes printed circuit board layout similar to that of Maxim’s evaluation kit.
Output Impedance
Third-Order Intercept
Spurious-Free Dynamic Range
1dB Gain Compression
Input Noise Voltage Density
Input Noise Current Density
Input Capacitance (Note 7)
CC
CC
-1
-2
-3
-4
-5
-6
_______________________________________________________________________________________
3
1
4
2
0
= +5V, V
= +5V, V
1
SMALL-SIGNAL GAIN vs. FREQUENCY
PARAMETER
tabulated in the Applications Information section of this data sheet.
based on the combination of worst-case design simulations along with a sample characterization of units. These minimum
specifications are for design guidance only and are not intended to guarantee AC performance (see AC Testing/
Performance ). For 100% testing of these parameters, contact the factory.
video signal amplitude developed by the International Radio Engineers. 140IRE = 1V.
V
IN
L
= 20mVp-p
= 100Ω, T
EE
EE
10
= -5V, R
= -5V, SHDN = 5V, V
FREQUENCY (MHz)
(A
MAX4223
VCL
SO-8 PACKAGE
R
A
F
= +1)
= 560
100
L
= +25°C, unless otherwise noted.) (Note 4)
SOT23-6
R
= 100Ω, T
F
= 470
1000
SYMBOL
i
SFDR
n
Z
A
+, i
C
IP3
OUT
e
CM
= +25°C, unless otherwise noted.)
IN
n
n
-
= 0V, A
f = 10kHz
f = 30kHz
f z = 30.1MHz
f = 10kHz
f = 10kHz
f = 10kHz
f = 10kHz
SO-8, SO-14
packages
SOT23-6, 10-pin µMAX
packages
-1
-2
-3
-4
-5
-6
4
3
2
1
0
V
1
= +1V/V for MAX4223/MAX4225/MAX4226, A
SMALL-SIGNAL GAIN vs. FREQUENCY
V
IN
= 20mVp-p
A
= +25°C. Specifications over temperature limits are guaranteed by design.
10
FREQUENCY (MHz)
F
(A
A
R
R
CONDITIONS
V
F
G
and R
MAX4223
VCL
= +5V/V
= 100
= 25
= +2/+5)
100
A
R
G
V
F
. These values vary for product and package type, and are
= +2V/V
= R
G
= 200
MAX4223/5/6
MAX4224/7/8
MAX4223/5/6
MAX4224/7/8
IN+
IN-
Pin to pin
Pin to GND
Pin to pin
Pin to GND
1000
-1
-2
-3
-4
-5
-6
3
1
4
2
0
1
MIN
V
LARGE-SIGNAL GAIN vs. FREQUENCY
A
R
V
= +2V/V for MAX4224/MAX4227/
V
F
OUT
MAX4223/MAX4225/MAX4226
= 560
= +1V/V
= 2Vp-p
10
TYP
-61
-62
0.3
1.0
0.3
0.8
FREQUENCY (MHz)
42
36
20
20
2
2
3
(A
VCL
= +1)
100
MAX
1000
pA/√Hz
nV/√Hz
UNITS
dBm
dBm
dB
pF
Ω