24FC515-I/SM Microchip Technology, 24FC515-I/SM Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
24FC515-I/SM
Manufacturer Part Number
24FC515-I/SM
Description
IC EEPROM 512KBIT 1MHZ 8SOIC
Manufacturer
Microchip Technology
Datasheet
1.24LC515-ISM.pdf
(24 pages)
Specifications of 24FC515-I/SM
Memory Size
512K (64K x 8)
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
1MHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
Memory Configuration
64K X 8
Ic Interface Type
I2C
Clock Frequency
1MHz
Supply Voltage Range
2.5V To 5.5V
Memory Case Style
SOIC
No. Of Pins
8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
24FC515I/SM
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
24FC515-I/SM
Manufacturer:
MCP
Quantity:
594
Company:
Part Number:
24FC515-I/SM
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
24FC515-I/SM
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
5.0
A control byte is the first byte received following the
Start condition from the master device (Figure 5-1).
The control byte consists of a 4-bit control code; for the
24XX515, this is set as ‘1010’ binary for read and write
operations. The next bit of the control byte is the block
select bit (B0). This bit acts as the A15 address bit for
accessing the entire array. The next two bits of the
control byte are the Chip Select bits (A1, A0). The Chip
Select bits allow the use of up to four 24XX515 devices
on the same bus and are used to select which device is
accessed. The Chip Select bits in the control byte must
correspond to the logic levels on the corresponding A1
and A0 pins for the device to respond. These bits are in
effect the two Most Significant bits of the word address.
The last bit of the control byte defines the operation to
be performed. When set to a ‘1’, a read operation is
selected, and when set to a ‘0’, a write operation is
selected. The next two bytes received define the
address of the first data byte (Figure 5-2). Because
only A14…A0 are used, the upper address bit is a
“don’t care.” The upper address bits are transferred
first, followed by the Less Significant bits.
Following the Start condition, the 24XX515 monitors
the SDA bus checking the device type identifier being
transmitted. Upon receiving a ‘1010’ code and appro-
priate device select bits, the slave device outputs an
Acknowledge signal on the SDA line. Depending on the
state of the R/W bit, the 24XX515 will select a read or
write operation.
This device has an internal addressing boundary
limitation that is divided into two segments of 256K bits.
Block select bit ‘B0’ is used in place of address bit
location ‘A15’ to control access to each segment.
FIGURE 5-2:
© 2008 Microchip Technology Inc.
1
Control
Code
DEVICE ADDRESSING
0
1
Control Byte
0
Select
Block
Bit
B
0
ADDRESS SEQUENCE BIT ASSIGNMENTS
A
1
Select
Chip
Bits
A
0 R/W
x
24AA515/24LC515/24FC515
14
A
Address High Byte
13
A
12
A
11
A
10
A
FIGURE 5-1:
5.1
The Chip Select bits A1, A0 can be used to expand the
contiguous address space for up to 2 Mbit by adding up
to four 24XX515’s on the same bus. In this case,
software can use A0 of the control byte as address bit
A16 and A1 as address bit A17. It is not possible to
sequentially read across device boundaries.
Each device has internal addressing boundary
limitations. This divides each part into two segments of
256K bits. The block select bit ‘B0’ controls access to
each “half” rather than address bit location A15.
Sequential read operations are limited to 256K blocks.
To read through four devices on the same bus, eight
random Read commands must be given.
Start Bit
A
9
S
A
8
Contiguous Addressing Across
Multiple Devices
1
Control Code
0
A
7
Slave Address
1
•
CONTROL BYTE
FORMAT
Address Low Byte
•
0
Select
Block
•
Bit
B0
Read/Write Bit
X = “don’t care” bit
Acknowledge Bit
•
A1
Select
Chip
Bits
•
DS21673G-page 7
A0
•
R/W
A
0
ACK