LYT4311E Power Integrations, LYT4311E Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/5/532/power_integrations_sml.jpg)
LYT4311E
Manufacturer Part Number
LYT4311E
Description
LED Lighting Drivers HighPower LED Driver 12W Dimmable
Manufacturer
Power Integrations
Datasheet
1.LYT4316E.pdf
(20 pages)
Specifications of LYT4311E
Rohs
yes
Input Voltage
85 V to 132 V
Operating Frequency
124 kHz to 140 kHz
Maximum Supply Current
3 mA
Output Current
0.86 A
Maximum Operating Temperature
+ 150 C
Mounting Style
Through Hole
Package / Case
eSIP-7C
Minimum Operating Temperature
- 40 C
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LYT4311E
Manufacturer:
POWER
Quantity:
15 000
Part Number:
LYT4311E
Manufacturer:
POWER
Quantity:
20 000
Figure 7.
5.9 V Regulator/Shunt Voltage Clamp
The internal 5.9 V regulator charges the bypass capacitor
connected to the BYPASS pin to 5.9 V by drawing a current
from the voltage on the DRAIN pin whenever the power FET is
off. The BYPASS pin is the internal supply voltage node. When
the power FET is on, the device operates from the energy stored
in the bypass capacitor. Extremely low power consumption of the
internal circuitry allows LYTSwitch to operate continuously from
current it takes from the DRAIN pin. A bypass capacitor value
of 47 or 4.7 µF is sufficient for both high frequency decoupling
and energy storage. In addition, there is a 6.4 V shunt regulator
clamping the BYPASS pin at 6.4 V when current is provided to
the BYPASS pin through an external resistor. This facilitates
powering of LYTSwitch externally through a bias winding to
increase operating efficiency. It is recommended that the
BYPASS pin is supplied current from the bias winding for
normal operation.
Auto-Restart
In the event of an open-loop fault (open FEEDBACK pin resistor
or broken path to feedback winding), output short-circuits or an
overload condition the controller enters into the auto-restart
mode. The controller annunciates both short-circuit and
open-loop conditions once the FEEDBACK pin current falls
below the I
the power dissipation under this fault condition the shutdown/
auto-restart circuit turns the power supply on (same as the
soft-start period) and off at an auto-restart duty cycle of
typically DC
fault is removed during the auto-restart off-time, the power
supply will remain in auto-restart until the full off-time count is
www.powerint.com
Remote ON/OFF VOLTAGE MONITOR Pin Control.
FB(AR)
AR
for as long as the fault condition persists. If the
threshold after the soft-start period. To minimize
D
S
CONTROL
R
V
FB
BP
PI-5435-052510
completed. Special consideration must be made to appropriately
size the output capacitor to ensure that after the soft-start
period (t
threshold to ensure successful power-supply start-up.
After the soft-start time period, auto-restart is activated only
when the FEEDBACK pin current falls below I
Over-Current Protection
The current limit circuit senses the current in the power FET.
When this current exceeds the internal threshold (I
FET is turned off for the remainder of that cycle. A leading edge
blanking circuit inhibits the current limit comparator for a short
time (t
blanking time has been set so that current spikes caused by
capacitance and rectifier reverse recovery will not cause
premature termination of the power FET conduction.
Line Overvoltage Protection
This device includes overvoltage detection to limit the maximum
operating voltage detected through the VOLTAGE MONITOR pin.
An external peak detector consisting of a diode and capacitor is
required to provide input line peak voltage to the VOLTAGE
MONITOR pin through a resistor.
The resistor sets line overvoltage (OV) shutdown threshold which,
once exceeded, forces the LYTSwitch to stop switching. Once
the line voltage returns to normal, the device resumes normal
operation. A small amount of hysteresis is provided on the OV
threshold to prevent noise-generated toggling. When the power
FET is off, the rectified DC high voltage surge capability is
increased to the voltage rating of the power FET (670 V), due to the
absence of the reflected voltage and leakage spikes on the drain.
Hysteretic Thermal Shutdown
The thermal shutdown circuitry senses the controller die
temperature. The threshold is set at 142 °C typical with a 75 °C
hysteresis. When the die temperature rises above this threshold
(142 °C) the power FET is disabled and remains disabled until
the die temperature falls by 75 °C, at which point the power FET
is re-enabled.
Safe Operating Area (SOA) Protection
The device also features a safe operating area (SOA) protection
mode which disables FET switching for 40 cycles in the event
the peak switch current reaches the I
on-time is less than t
device under short-circuited LED conditions and at start-up during
the soft-start period when auto-restart protection is inhibited.
The SOA protection mode remains active in normal operation.
LEB
SOFT
) after the power FET is turned on. This leading edge
) the FEEDBACK pin current is above the I
ON(SOA)
LYT4211-4218/4311-4318
. This protection mode protects the
LIMIT
threshold and the switch
FB(AR)
LIMIT
.
), the power
FB(AR)
Rev. B 02/13
5