24VL014/SN Microchip Technology, 24VL014/SN Datasheet - Page 5

• Manufacturer Part Number: 24VL014/SN
• Description: IC EEPROM 1KBIT 400KHZ 8SOIC
• Manufacturer: Microchip Technology

Specifications of 24VL014/SN

• Memory Size: 1K (128 x 8)
• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Speed: 100kHz, 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.5 V ~ 3.6 V
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Memory Configuration: 128 X 8 / 64 X 16
• Ic Interface Type: I2C
• Clock Frequency: 400kHz
• Supply Voltage Range: 1.5V To 3.6V
• Memory Case Style: SOIC
• No. Of Pins: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2.0
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
2.1
This is a bidirectional pin used to transfer addresses
and data into and out of the device. It is an open drain
terminal. Therefore, the SDA bus requires a pull-up
resistor to V
400 kHz).
For normal data transfer, SDA is allowed to change
only during SCL low. Changes during SCL high are
reserved for indicating the Start and Stop conditions.
2.2
The SCL input is used to synchronize the data transfer
to and from the device.
2.3
The A0, A1 and A2 inputs are used by the 24VL014 for
multiple device operations. The levels on these inputs
are compared with the corresponding bits in the slave
address. The chip is selected if the compare is true.
Up to eight 24VL014 devices (four for the SOT-23
package) may be connected to the same bus by using
different Chip Select bit combinations. These inputs
must be connected to either V
In most applications, the chip address inputs A0, A1
and A2 are hard-wired to logic ‘0’ or logic ‘1’. For
applications in which these pins are controlled by a
microcontroller or other programmable device, the chip
address pins must be driven to logic ‘0’ or logic ‘1’
before normal device operation can proceed.
2.4
WP is the hardware write-protect pin. It must be tied to
V
is enabled and will protect the entire array (00h-7Fh). If
the WP pin is tied to V
is disabled. Write Protection is not available on the
SOT-23 package; for this package, write operations are
always enabled.
© 2009 Microchip Technology Inc.
A0
A1
A2
V
SDA
SCL
WP
V
CC
SS
CC
Name
or V
SS
PIN DESCRIPTIONS
SDA Serial Data
SCL Serial Clock
A0, A1, A2
WP
. If tied to V
CC
8-pin
PDIP
(typical 10 kΩ for 100 kHz, 2 kΩ for
1
2
3
4
5
6
7
8
PIN FUNCTION TABLE
CC
SS
, the hardware write protection
the hardware write protection
8-pin
SOIC
1
2
3
4
5
6
7
8
CC
or V
SS
TSSOP
8-pin
.
1
2
3
4
5
6
7
8
MSOP
8-pin
1
2
3
4
5
6
7
8
TDFN
8-pin
2.5
The 24VL014 employs a V
that disables the internal erase/write logic if the V
below 1.0 volts at nominal conditions.
The SCL and SDA inputs have Schmitt Trigger and
filter circuits that suppress noise spikes to assure
proper device operation even on a noisy bus.
1
2
3
4
5
6
7
8
Noise Protection
SOT-23
6-pin
—
—
5
4
2
3
1
6
User Configurable Chip Select
User Configurable Chip Select
User Configurable Chip Select
Ground
Serial Data
Serial Clock
Write-Protect Input
+1.5V to 3.6V
CC
threshold detector circuit
24VL014
Function
DS22129A-page 5
CC
is