MAX8727ETB-T Maxim Integrated, MAX8727ETB-T Datasheet
MAX8727ETB-T
Related parts for MAX8727ETB-T
MAX8727ETB-T Summary of contents
Page 1
... Adjustable Output from V ♦ 2.6V to 5.5V Input Supply Range ♦ Input Supply Undervoltage Lockout ♦ Pin-Programmable 640kHz/1.2MHz Switching Frequency ♦ Programmable Soft-Start ♦ 0.1µA Shutdown Current ♦ Small 10-Pin Thin DFN Package Applications PART MAX8727ETB MAX8727ETB+ +Denotes lead-free package. V 2. FREQ ...
Page 2
TFT-LCD Step-Up DC-DC Converter ABSOLUTE MAXIMUM RATINGS LX to GND ..............................................................-0.3V to +26V IN, SHDN, FREQ GND ...................................-0.3V to +6V COMP GND .........................................-0. Switch Maximum Continuous RMS Current .....................2.4A Continuous Power Dissipation (T ...
Page 3
TFT-LCD Step-Up DC-DC Converter ELECTRICAL CHARACTERISTICS (continued 3V, FREQ = GND 0°C to +85°C. Typical values are at T SHDN IN A PARAMETER CONTROL INPUTS SHDN, FREQ Input Low Voltage V IN SHDN, FREQ ...
Page 4
TFT-LCD Step-Up DC-DC Converter ELECTRICAL CHARACTERISTICS (continued 3V, FREQ = GND -40°C to +85°C, unless otherwise noted.) (Note 1) SHDN IN A PARAMETER CONTROL INPUTS SHDN, FREQ Input Low Voltage V IN SHDN, FREQ ...
Page 5
TFT-LCD Step-Up DC-DC Converter (Circuit of Figure 5V 15V MAIN SOFT-START (R = 30Ω) LOAD 1ms/div PULSED LOAD-TRANSIENT RESPONSE (I = 100mA TO 1.1A) LOAD 1μs/div _______________________________________________________________________________________ Typical Operating Characteristics (continued) = +25°C ...
Page 6
TFT-LCD Step-Up DC-DC Converter PIN NAME Compensation Pin for Error Amplifier. Connect a series RC from COMP to ground. See the Loop 1 COMP Compensation section for component selection guidelines. Feedback Pin. The FB regulation voltage is 1.24V nominal. Connect ...
Page 7
TFT-LCD Step-Up DC-DC Converter SHDN COMP FB 1.24V FREQ OSCILLATOR 5μA Figure 2. MAX8727 Functional Diagram Detailed Description The MAX8727 is a highly efficient power supply that employs a current-mode, fixed-frequency, pulse-width modulation (PWM) architecture for fast transient response and ...
Page 8
TFT-LCD Step-Up DC-DC Converter The MAX8727 can be programmed for soft-start upon power-up with an external capacitor. When the shutdown pin is taken high, the soft-start capacitor (C ately charged to 0.4V. Then the capacitor is charged at a constant ...
Page 9
TFT-LCD Step-Up DC-DC Converter The equations used here include a constant LIR, which is the ratio of the inductor peak-to-peak ripple current to the average DC inductor current at the full load cur- rent. The best trade-off between inductor size ...
Page 10
TFT-LCD Step-Up DC-DC Converter Input Capacitor Selection The input capacitor (C ) reduces the current peaks IN drawn from the input supply and reduces noise injection into the IC. A 10µF ceramic capacitor is used in the typi- cal operating ...
Page 11
TFT-LCD Step-Up DC-DC Converter V2 +28V C9 1μ 4. 10μF 10Ω 6.3V C5 1μF C4 33nF Figure 3. Multiple-Output TFT-LCD Power Supply Multiple-Output Power Supply for TFT LCD Figure 3 shows a power supply ...
Page 12
TFT-LCD Step-Up DC-DC Converter 3) Place the feedback voltage-divider-resistors as close to the FB pin as possible. The divider’s center trace should be kept short. Placing the resistors far away causes the FB trace to become an antenna that can ...
Page 13
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © 2005 Maxim Integrated Products ...