MAX1533EVKIT Maxim Integrated, MAX1533EVKIT Datasheet - Page 2

• Manufacturer Part Number: MAX1533EVKIT
• Description: Current & Power Monitors & Regulators Evaluation Kit for the MAX1533
• Manufacturer: Maxim Integrated

Specifications of MAX1533EVKIT

• Product: Power Monitors
• Supply Voltage - Max: 24 V
• Supply Voltage - Min: 6 V
• Operating Temperature Range: - 40 C to + 85 C
• Accuracy: 1 %
• Input Voltage Range: 6 V to 24 V
• Supply Current: 35 uA

MAX1533 Evaluation Kit
Note: Indicate that you are using the MAX1533 when contacting these suppliers.
2
Central Semiconductor
Diodes Incorporated
Fairchild Semiconductor
IRC (International Resistive Company)
Kemet
Murata
Sanyo
Sumida
TDK
Vishay
DESIGNATION
R4–R12, R16,
_______________________________________________________________________________________
R19–R24
N1, N3
N2, N4
R1, R2
L1, L2
None
None
R14
R15
R3
U1
Component List (continued)
SUPPLIER
QTY
2
2
2
2
1
0
1
0
1
1
7
5.8µH, 8.6A, 16.2mΩ inductors
Sumida CDRH127/LD-5R8NC
8.4A, 30V n-channel MOSFETs, SO-8
Fairchild FDS6612A
13A, 30V n-channel MOSFETs, SO-8
Fairchild FDS6670A
0.01Ω ±1%, 0.5W sense resistor
(2010)
IRC LRC-LRF2010-01-R010-F
Vishay Dale WSL2010 0.010 1.0%
20Ω ±5% resistor (0603)
Not installed, resistors (0603)
100kΩ ±5% resistor (0603)
Not installed, resistor (1206)
MAX1533ETJ, 32-pin thin QFN
(5mm x 5mm)
MAX1533 EV Kit PC board
Shunts
DESCRIPTION
631-435-1110
805-446-4800
888-522-5372
361-992-7900
864-963-6300
770-436-1300
619-661-6835
847-545-6700
847-803-6100
402-564-3131
PHONE
Before beginning, the following equipment is recom-
mended:
• 6V to 24V, 100W, DC power supply
• Dummy loads capable of sinking 5A
• 3 voltmeters
• An oscilloscope
The MAX1533 EV kit is a fully assembled and tested
surface-mount board. Follow the steps below to verify
board operation. Do not turn on the power supply
until all connections are completed.
1) Verify that the shunts are in the following positions:
2) Connect the power supply across the VIN and
3) Connect a voltmeter across the 5V_MAIN and
4) Connect a voltmeter across the 3.3V_MAIN and
5) Turn on the power supply.
6) Verify the output voltages.
PGND pads.
PGND pads.
PGND pads.
JU1 = 1-2 (overvoltage protection disabled)
JU2 = 1-2 (MAX1533 enabled)
JU3 = 1-2 (undervoltage protection disabled)
JU4 = 1-2 (PWM mode)
JU5 = 1-2 (5V main output enabled)
JU6 = 1-2 (3.3V main output enabled)
JU8 = 3-4 (300kHz operation)
631-435-1824
805-446-4850
361-992-3377
864-963-6322
770-436-3030
619-661-1055
847-545-6720
847-390-4405
402-563-6296
FAX
—
Component Suppliers
Recommended Equipment
www.centralsemi.com
www.diodes.com
www.fairchildsemi.com
www.irctt.com
www.kermit.com
www.murata.com
www.sanyodevice.com
www.sumida.com
www.component.tdk.com
www.vishay.com
Quick Start
WEBSITE
Procedure