24AA08T-I/MNY Microchip Technology, 24AA08T-I/MNY Datasheet - Page 11

• Manufacturer Part Number: 24AA08T-I/MNY
• Description: IC EEPROM 8KBIT 400KHZ 8TDFN
• Manufacturer: Microchip Technology

Specifications of 24AA08T-I/MNY

• Memory Size: 8K (4 x 256 x 8)
• Package / Case: 8-TDFN
• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Speed: 100kHz, 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Organization: 4 Block x 256 x 8
• Interface Type: I2C
• Maximum Clock Frequency: 0.1 MHz
• Access Time: 3500 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.7 V
• Maximum Operating Current: 3 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 1.8 V , 2.5 V , 3.3 V , 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 24AA08T-I/MNYTR

8.0
The descriptions of the pins are listed in Table 8-1.
TABLE 8-1:
8.1
SDA is a bidirectional pin used to transfer addresses
and data into and out of the device. Since it is an open-
drain terminal, the SDA bus requires a pull-up resistor
to V
For normal data transfer, SDA is allowed to change
only during SCL low. Changes during SCL high are
reserved for indicating Start and Stop conditions.
8.2
The SCL input is used to synchronize the data transfer
to and from the device.
© 2008 Microchip Technology Inc.
Name
SDA
SCL
V
V
WP
CC
A0
A1
A2
SS
CC
(typical 10 kΩ for 100 kHz, 2 kΩ for 400 kHz).
PIN DESCRIPTIONS
Serial Address/Data Input/Output
(SDA)
Serial Clock (SCL)
PDIP
4
7
8
1
2
3
5
6
PIN FUNCTION TABLE
SOIC
1
2
3
4
5
6
7
8
TSSOP
1
2
3
4
5
6
7
8
DFN
1
2
3
4
5
6
7
8
TDFN
1
2
3
4
5
6
7
8
8.3
The WP pin must be connected to either V
If tied to V
(read/write the entire memory 000-03FF).
If tied to V
memory will be write-protected. Read operations are
not affected.
This feature allows the user to use the 24XX08 as a
serial ROM when WP is enabled (tied to V
8.4
The A0, A1 and A2 pins are not used by the 24XX08.
They may be left floating or tied to either V
MSOP
1
2
3
4
5
6
7
8
24AA08/24LC08B
Write-Protect (WP)
A0, A1, A2
CC
SS
, write operations are inhibited. The entire
, normal memory operation is enabled
SOT-23
—
—
—
2
3
1
5
4
Ground
Write-Protect Input
+1.7V to 5.5V Power Supply
Not Connected
Not Connected
Not Connected
Serial Address/Data I/O
Serial Clock
Description
DS21710H-page 11
CC
SS
SS
).
or V
or V
CC
CC
.
.