MC74LCX16244DT ON Semiconductor, MC74LCX16244DT Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
MC74LCX16244DT
Manufacturer Part Number
MC74LCX16244DT
Description
Buffers & Line Drivers 2-36.V CMOS 16-Bit
Manufacturer
ON Semiconductor
Datasheet
1.MC74LCX16244DT.pdf
(7 pages)
Specifications of MC74LCX16244DT
Product Category
Buffers & Line Drivers
Number Of Input Lines
16
Number Of Output Lines
3
Polarity
Non-Inverting
Supply Voltage - Max
3.6 V
Supply Voltage - Min
2 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
TSSOP-48
High Level Output Current
- 24 mA
Logic Family
LCX
Logic Type
CMOS
Low Level Output Current
24 mA
Maximum Power Dissipation
200 mW
Minimum Operating Temperature
- 40 C
Number Of Channels Per Chip
16
Output Type
3-State
Propagation Delay Time
5.2 ns at 2.7 V, 4.5 ns at 3.3 V
Factory Pack Quantity
39
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC74LCX16244DT
Manufacturer:
ON/安森美
Quantity:
20 000
Company:
Part Number:
MC74LCX16244DTG
Manufacturer:
ON Semiconductor
Quantity:
1 550
Part Number:
MC74LCX16244DTR2
Manufacturer:
ON/安森美
Quantity:
20 000
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
−T−
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor and
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
0.076 (0.003)
SEATING
PLANE
PIN 1
IDENT.
D
L
C
48
1
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
48X
K
0.12 (0.005)
REF
−V−
A
G
1
M
T
0.32
48X
U
S
N. American Technical Support: 800−282−9855 Toll Free
Europe, Middle East and Africa Technical Support:
Japan Customer Focus Center
PACKAGE DIMENSIONS
SOLDERING FOOTPRINT
USA/Canada
Phone: 421 33 790 2910
Phone: 81−3−5817−1050
V
S
RECOMMENDED
http://onsemi.com
25
24
DT SUFFIX
CASE 1201
TSSOP−48
−U−
B
ISSUE B
H
7
N
J
DETAIL E
DETAIL E
N
PITCH
0.50
Ç Ç Ç
É É É
J1
Ç Ç Ç
É É É
SECTION N−N
F
DIMENSIONS: MILLIMETERS
K1
K
0.25 (0.010)
M
1.00
−W−
48X
8.45
NOTES:
1. DIMENSIONING AND TOLERANCING PER
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
4. DIMENSION K DOES NOT INCLUDE DAMBAR
5. TERMINAL NUMBERS ARE SHOWN FOR
6. DIMENSIONS A AND B ARE TO BE
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
ANSI Y14.5M, 1982.
MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH OR GATE BURRS
SHALL NOT EXCEED 0.15 (0.006) PER SIDE.
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL
IN EXCESS OF THE K DIMENSION AT
MAXIMUM MATERIAL CONDITION.
REFERENCE ONLY.
DETERMINED AT DATUM PLANE −W−.
DIM
K1
J1
A
B
C
D
G
H
K
M
F
J
L
12.40
MILLIMETERS
MIN
6.00
0.05
0.50
0.37
0.09
0.09
0.17
0.17
7.95
−−−
0.50 BSC
0
_
12.60
MAX
6.20
1.10
0.15
0.75
0.20
0.16
0.27
0.23
8.25
−−−
MC74LCX16244/D
8
_
0.488
0.236
0.002
0.020
0.015
0.004
0.004
0.007
0.007
0.313
MIN
0.0197 BSC
−−−
0
INCHES
_
0.496
0.244
0.043
0.006
0.030
0.008
0.006
0.009
0.325
0.011
MAX
−−−
8
_