11AA010-I/P Microchip Technology, 11AA010-I/P Datasheet - Page 7
![IC EEPROM 1KBIT 100KHZ 8DIP](/photos/7/21/72169/11aa010-i_p_sml.jpg)
11AA010-I/P
Manufacturer Part Number
11AA010-I/P
Description
IC EEPROM 1KBIT 100KHZ 8DIP
Manufacturer
Microchip Technology
Specifications of 11AA010-I/P
Memory Size
1K (128 x 8)
Package / Case
8-DIP (0.300", 7.62mm)
Operating Temperature
-40°C ~ 85°C
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
100kHz
Interface
UNI/O™ (Single Wire)
Voltage - Supply
1.8 V ~ 5.5 V
Organization
128 x 8
Interface Type
Serial
Maximum Clock Frequency
100 KHz
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V
Maximum Operating Current
50 uA
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
1.8 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
11AA010-I/P
Manufacturer:
MICROCHIP
Quantity:
12 000
3.0
3.1
When the master has control of SCIO, a standby pulse
can be generated by holding SCIO high for T
this time, the 11XX will reset and return to Standby
mode. Subsequently, a high-to-low transition on SCIO
(the first low pulse of the header) will return the device
to the active state.
Once a command is terminated satisfactorily (i.e., via
a NoMAK/SAK combination during the Acknowledge
sequence), performing a standby pulse is not required
to begin a new command as long as the device to be
selected is the same device selected during the previ-
ous command. However, a period of T
observed after the end of the command and before the
beginning of the start header. After T
header (including T
in order to begin the new command.
FIGURE 3-1:
3.2
All operations must be preceded by a start header. The
start header consists of holding SCIO low for a period
of T
code. This code is used to synchronize the slave’s
internal clock period with the master’s clock period, so
accurate timing is very important.
FIGURE 3-2:
2010 Microchip Technology Inc.
SCIO
HDR
SCIO
SCIO
Note 1: After a POR/BOR event, a low-to-high transition on SCIO is required to occur before the first
, followed by transmitting an 8-bit ‘
BUS CHARACTERISTICS
Standby Pulse
Start Data Transfer
T
SS
standby pulse.
Standby Pulse
HDR
T
HDR
CONSECUTIVE COMMANDS EXAMPLE
START HEADER
low pulse) can be transmitted
Data ‘0’ Data ‘1’ Data ‘0’ Data ‘1’ Data ‘0’ Data ‘1’ Data ‘0’ Data ‘1’
(1)
0
Start Header
1
0
SS
01010101
SS
1
, the start
0
must be
STBY
0
Start Header
1
1
. At
Preliminary
0
0
’
1
1
0
1
If a command is terminated in any manner other than a
NoMAK/SAK combination, then the master must per-
form a standby pulse before beginning a new com-
mand, regardless of which device is to be selected.
An example of two consecutive commands is shown in
Figure 3-1. Note that the device address is the same
for both commands, indicating that the same device is
being selected both times.
A standby pulse cannot be generated while the slave
has control of SCIO. In this situation, the master must
wait for the slave to finish transmitting and to release
SCIO before the pulse can be generated.
If, at any point during a command, an error is detected
by the master, a standby pulse should be generated
and the command should be performed again.
When a standby pulse is not required (i.e., between
successive commands to the same device), a period of
T
and before the beginning of the start header.
Figure 3-2 shows the waveform for the start header,
including the required Acknowledge sequence at the
end of the byte.
1
SS
0
Note: After a POR/BOR event occurs, a low-
11AAXXX/11LCXXX
0
must be observed after the end of the command
Device Address
1
1
to-high transition on SCIO must be gen-
erated before proceeding with communi-
cation, including a standby pulse.
0
0
1
0
0
Device Address
0
1
0
0
0
0
0
MAK
0
DS22067H-page 7
NoSAK