DS21458-W+ Maxim Integrated, DS21458-W+ Datasheet - Page 121
DS21458-W+
Manufacturer Part Number
DS21458-W+
Description
Network Controller & Processor ICs
Manufacturer
Maxim Integrated
Datasheet
1.DS21458-W.pdf
(269 pages)
Specifications of DS21458-W+
Product
Framer
Number Of Transceivers
4
Data Rate
64 Kbps
Supply Current (max)
328 mA
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Package / Case
CSBGA
Minimum Operating Temperature
0 C
Operating Supply Voltage
3.3 V
Supply Voltage - Max
3.465 V
Supply Voltage - Min
3.135 V
Part # Aliases
90-21458+W00
- Current page: 121 of 269
- Download datasheet (2Mb)
DS21455/DS21458 Quad T1/E1/J1 Transceivers
20.4 Minimum-Delay Mode
When minimum delay mode is enabled the elastic stores will be forced to a maximum depth of 32 bits
instead of the normal two-frame depth. ESCR.5 and ESCR.1 enable the transmit and receive elastic store
minimum-delay modes. This feature is useful primarily in applications that interface T1 to a 2.048MHz
bus without adding the latency that would be associated with using the elastic store in full buffer mode.
Certain restrictions apply when minimum delay mode is used. Minimum-delay mode can only be
used when the elastic store’s system clock is locked to its network clock (e.g., RCLK locked to
RSYSCLK for the receive side and TCLK locked to TSYSCLK for the transmit side). RSYNC must be
configured as an output. In E1 operation TSYNC must be configured as an input when transmit
minimum delay mode is enabled. In T1 operation TSYNC can be configured as an input or output when
transmit minimum delay mode is enabled. In a typical application RSYSCLK and TSYSCLK are locked
to RCLK, and RSYNC (frame output mode) is connected to TSSYNC (frame input mode). All of the slip
contention logic in the framer is disabled (since slips cannot occur). On power-up, after the RSYSCLK
and TSYSCLK signals have locked to their respective network clock signals, the elastic store reset bits
(ESCR.2 and ESCR.6) should be toggled from a zero to a one to ensure proper operation.
121 of 269
Related parts for DS21458-W+
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC LIU QUAD T1/E1/J1 256-CSBGA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Network Controller & Processor ICs Quad E1-T1-J1 Single -Chip Transceiver (S
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
power light source Luxeon Line
Manufacturer:
LUMILEDS [Lumileds Lighting Company]
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products