5173N24-U THAT, 5173N24-U Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
5173N24-U
Manufacturer Part Number
5173N24-U
Description
Microphone Preamplifiers 36V, 100mA
Manufacturer
THAT
Datasheet
1.5173N24-U.pdf
(20 pages)
Specifications of 5173N24-U
Rohs
yes
Common Mode Rejection Ratio (min)
- 9 dB
Input Offset Voltage
- 1.75 mV to + 1.75 mV
Maximum Operating Temperature
+ 85 C
Package / Case
QFN-24
Input Voltage Range (max)
3.6 V, 17 V
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Operating Supply Voltage
3 V to 3.6 V, 4.75 V to 17 V
Operating Temperature Range
- 40 C to + 85 C
Supply Current
2 uA, 7.6 mA
Supply Voltage - Max
3.6 V, 17 V
Supply Voltage - Min
3 V, 4.75 V
Thd Plus Noise
0.001 %
Voltage Gain Db
60 dB
Document 600166 Rev 01
Multiple Devices with Separate Chip
Selects
devices by using separate chip selects as shown in
Figure 6. The advantage of this method over daisy
chaining is that any of the N 5173 devices may be
updated with a single 16-bit SPI operation (as
opposed to the long Nx16 bit data stream required
when N devices are daisy chained). The disadvantage
of this method is N different chip selects must be
supplied to the individual devices.
Figure 6. Multiple 5173 ICs connected in parallel to a host
microcontroller, with independent chip selects.
The SPI port can be operated with multiple
SPI Port
Microcontroller
Host
MISO
SCLK
MOSI
GPIO
GPIO
GPIO
Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com
THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA
Copyright © 2012, THAT Corporation; All rights reserved.
DI
DOUT
SCLK
CS
DI
DOUT
SCLK
CS
DI
DOUT
SCLK
CS
THAT5173
THAT5173
THAT5173
#1
#2
#3
SPI Port
SPI Port
SPI Port
Page 10 of 20
Daisy Chaining
ing the DOUT of device n to the DIN pin of device
n+1, as shown in Figure 7. Data is loaded by hold-
ing the common CS low for 16 x N SCLK pulses,
where N = total number of devices in the daisychain.
All devices are simultaneously updated on the rising
edge of CS, particularly useful in applications where
updates to a large number of channels must be syn-
chronized. Another advantage of this method is one
chip select can be shared by all devices, simplifying
the digital control circuitry on the PCB. The disad-
vantage is all N devices must be updated as a group,
thereby slowing down the rate of control to each indi-
vidual device.
Figure 7. Multiple 5173 ICs connected in a daisy-chained
Multiple devices can be daisy-chained by connect-
Microcontroller
SPI Port
Host
MOSI
MISO
SCLK
GPIO
mode to a host microcontroller.
Audio Preamplifier Digital Controller IC
DI
DOUT
SCLK
CS
DI
DOUT
SCLK
CS
DI
DOUT
SCLK
CS
THAT5173
THAT5173
THAT5173
#1
#2
#3
THAT5173
SPI Port
SPI Port
SPI Port