CAT25020HU4I-GT3 ON Semiconductor, CAT25020HU4I-GT3 Datasheet
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
CAT25020HU4I-GT3
Specifications of CAT25020HU4I-GT3
Related parts for CAT25020HU4I-GT3
CAT25020HU4I-GT3 Summary of contents
Page 1
... Page Write Buffer • Self−timed Write Cycle • Hardware and Software Protection • Block Write Protection − Protect 1/4, 1/2 or Entire EEPROM Array • Low Power CMOS Technology • 1,000,000 Program/Erase Cycles • 100 Year Data Retention • Industrial and Extended Temperature Range • ...
Page 2
Table 1. ABSOLUTE MAXIMUM RATINGS Operating Temperature Storage Temperature Voltage on any Pin with Respect to Ground (Note 1) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions ...
Page 3
Table 5. A.C. CHARACTERISTICS − Mature Product (T = −40°C to +85°C (Industrial) and Symbol Parameter f Clock Frequency SCK t Data Setup Time SU t Data Hold Time H t SCK High Time WH t SCK ...
Page 4
Table 7. A.C. CHARACTERISTICS – New Product (Rev −40°C to +85°C (Industrial) and Symbol Parameter f Clock Frequency SCK t Data Setup Time SU t Data Hold Time H t SCK High Time WH ...
Page 5
Pin Description SI: The serial data input pin accepts op−codes, addresses and data. In SPI modes (0,0) and (1,1) input data is latched on the rising edge of the SCK clock input. SO: The serial data output pin is used ...
Page 6
Table 10. STATUS REGISTER Table 11. BLOCK PROTECTION BITS Status Register Bits BP1 BP0 0 0 None 0 1 CAT25010: 060−07F, CAT25020: 0C0−0FF, CAT25040: 180−1FF 1 0 CAT25010: 040−07F, CAT25020: 080−0FF, CAT25040: 100−1FF 1 ...
Page 7
Byte Write Once the WEL bit is set, the user may execute a write sequence, by sending a WRITE instruction, a 8−bit address and data as shown in Figure 5. For the CAT25040, bit 3 of the write instruction opcode ...
Page 8
Write Status Register The Status Register is written by sending a WRSR instruction according to timing shown in Figure 7. Only bits 2 and 3 can be written using the WRSR command SCK OPCODE SI ...
Page 9
Read from Memory Array To read from memory, the host sends a READ instruction followed by a 8−bit address (for the CAT25040, bit 3 of the read instruction opcode contains A8 address bit). After receiving the last address bit, the ...
Page 10
Hold Operation The HOLD input can be used to pause communication between host and CAT25010/20/40. To pause, HOLD must be taken low while SCK is low (Figure 11). During the hold condition the device must remain selected (CS low). During ...
Page 11
PIN # 1 IDENTIFICATION D TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-001. PACKAGE DIMENSIONS PDIP−8, 300 mils CASE 646AA−01 ISSUE A SYMBOL ...
Page 12
PIN # 1 IDENTIFICATION TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD−01 ISSUE O SYMBOL ...
Page 13
E1 e TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL−01 ISSUE O SYMBOL MIN A A1 0.05 A2 ...
Page 14
D E PIN#1 INDEX AREA TOP VIEW SYMBOL MIN NOM A 0.70 0.75 A1 0.00 0.02 A2 0.45 0.55 A3 0.20 REF b 0.20 0.25 D 1.90 2.00 D2 1.30 1.40 E 2.90 3.00 E2 1.20 1.30 e 0.50 TYP ...
Page 15
E E1 TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-187. PACKAGE DIMENSIONS MSOP 8, 3x3 CASE 846AD−01 ISSUE O SYMBOL MIN A A1 ...
Page 16
D E PIN #1 INDEX AREA TOP VIEW SYMBOL MIN NOM A 0.45 0.50 A1 0.00 0.02 A3 0.127 REF b 0.20 0.25 D 1.95 2.00 D2 1.35 1.40 E 2.95 3.00 E2 1.25 1.30 e 0.50 REF L 0.25 ...
Page 17
... S01E CAT25010YE−GT3 S01E CAT25010YI−G S01E CAT25010YI−GT3 S01E CAT25010ZE−GT3 S0 CAT25010ZI−G S0 CAT25010ZI−GT3 S0 CAT25020HU4E−GT3 S1U CAT25020HU4I−GT3 S1U CAT25020LI−G 25020E CAT25020VE−GT3 25020E CAT25020VI−G 25020E CAT25020VI−GT3 25020E CAT25020VP2E−GT3 S1T (Note 17) CAT25020VP2I−GT3 S1T (Note 17) CAT25020YE− ...
Page 18
... For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. 19. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device Nomenclature document, TND310/D, available at www.onsemi.com ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) ...