MAX188CCAP-T Maxim Integrated, MAX188CCAP-T Datasheet
![no-image](/images/no-image-200.jpg)
MAX188CCAP-T
Specifications of MAX188CCAP-T
Related parts for MAX188CCAP-T
MAX188CCAP-T Summary of contents
Page 1
... Robotics Battery-Powered Instruments Medical Instruments SPI and QSPI are registered trademarks of Motorola. Microwire is a registered trademark of National Semiconductor. ________________________________________________________________ Maxim Integrated Products For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800 Low-Power, 8-Channel, Serial 12-Bit ADCs ____________________________Features 8-Channel Single-Ended or 4-Channel Differential Inputs Single +5V or ± ...
Page 2
Low-Power, 8-Channel, Serial 12-Bit ADCs ABSOLUTE MAXIMUM RATINGS V to AGND............................................................-0. AGND ............................................................+0. ..............................................................-0.3V to +12V DD SS AGND to DGND.....................................................-0.3V to +0.3V CH0–CH7 to AGND, DGND .............(V SS ...
Page 3
ELECTRICAL CHARACTERISTICS (continued ±5 -5V CLK 4.7µF capacitor at VREF pin; MAX188—external reference, VREF = 4.096V applied to VREF pin; T noted.) PARAMETER SYMBOL Small-Signal Bandwidth Full-Power Bandwidth CONVERSION RATE ...
Page 4
Low-Power, 8-Channel, Serial 12-Bit ADCs ELECTRICAL CHARACTERISTICS (continued ±5 -5V 2.0MHz, external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps); MAX186— CLK 4.7µF capacitor at VREF pin; MAX188—external reference, ...
Page 5
ELECTRICAL CHARACTERISTICS (continued ±5 -5V CLK 4.7µF capacitor at VREF pin; MAX188—external reference, VREF = 4.096V applied to VREF pin; T noted.) PARAMETER SYMBOL Positive Supply Rejection (Note 8) Negative ...
Page 6
Low-Power, 8-Channel, Serial 12-Bit ADCs __________________________________________Typical Operating Characteristics POWER-SUPPLY REJECTION vs. TEMPERATURE 0. +5V ± -5V SS 0.20 0.15 0.10 0.05 0.00 -0.05 -60 -40 - 100 ...
Page 7
Description (continued) PIN NAME Input to the Reference-Buffer Amplifier. To disable the reference-buffer amplifier, tie REFADJ to 12 REFADJ AGND Analog Ground. Also IN- Input for single-ended conversions. 14 DGND Digital Ground Serial Data Output. ...
Page 8
Low-Power, 8-Channel, Serial 12-Bit ADCs _______________Detailed Description The MAX186/MAX188 use a successive-approximation conversion technique and input track/hold (T/H) circuit convert an analog signal to a 12-bit digital output. A flexible serial interface provides easy interface to microprocessors. No ...
Page 9
MAX186 0V TO MAX188 4.096V CH7 ANALOG 0.01µF INPUT +5V D1 1N4148 REFADJ VREF C2 C1 0.01µF 4.7µF +2.5V +2.5V REFERENCE * FULL-SCALE ANALOG INPUT, CONVERSION RESULT = $FFF (HEX) **REQUIRED FOR MAX188 ONLY. A POTENTIOMETER MAY BE USED IN ...
Page 10
Low-Power, 8-Channel, Serial 12-Bit ADCs single-ended unipolar conversions on CH7 in external clock mode without powering down between conver- sions. In external clock mode, the SSTRB output pulses high for one clock period before the most significant bit of the ...
Page 11
Table 3. Channel Selection in Single-Ended Mode (SGL/ SEL2 SEL1 SEL0 CH0 Table 4. Channel ...
Page 12
Low-Power, 8-Channel, Serial 12-Bit ADCs CS t ACQ SCLK 1 4 START SEL2 SEL1 SEL0 UNI/ SCL/ DIN DIFF PD1 PD0 BIP SSTRB RB1 DOUT ACQUISITION IDLE A/D STATE 1.5µs (CLK = 2MHz) Figure 6. 24-Bit External Clock Mode Conversion ...
Page 13
CS t SDV SSTRB SCLK Figure 8. External Clock Mode SSTRB Detailed Timing CS SCLK START SEL2 SEL1 SEL0 UNI/ DIN DIP SSTRB DOUT IDLE A/D STATE Figure 9. Internal Clock Mode Timing In internal clock ...
Page 14
Low-Power, 8-Channel, Serial 12-Bit ADCs CS t CSH SSTRB SCLK PD0 CLOCK IN Figure 10. Internal Clock Mode SSTRB Detailed Timing The falling edge of CS does not start a conversion on the MAX186/MAX188. The first logic high clocked into ...
Page 15
CS 1 SCLK DIN S CONTROL BYTE 0 DOUT SSTRB Figure 11a. External Clock Mode, 15 Clocks/Conversion Timing CS SCLK S CONTROL BYTE 0 DIN DOUT Figure 11b. External Clock Mode, 16 Clocks/Conversion Timing Choosing Power-Down Mode You can save ...
Page 16
Low-Power, 8-Channel, Serial 12-Bit ADCs CLOCK INTERNAL MODE SHDN SETS EXTERNAL CLOCK MODE DIN DOUT DATA VALID (12 DATA BITS) POWERED UP MODE Figure 12a. Timing Diagram Power-Down Modes, External Clock Table ...
Page 17
CLOCK MODE SETS INTERNAL CLOCK MODE DIN DOUT SSTRB CONVERSION MODE Figure 12b. Timing Diagram Power-Down Modes, Internal Clock Hardware Power-Down The SHDN pin places the converter into the full power-down mode. ...
Page 18
Low-Power, 8-Channel, Serial 12-Bit ADCs MAX186 FULL POWER-DOWN 1000 2ms FASTPD WAIT 400kHz EXTERNAL CLOCK INTERNAL COMPENSATION 100 100 150 200 250 300 350 CONVERSIONS PER CHANNEL PER SECOND Figure 14a. MAX186 Supply Current vs. Sample ...
Page 19
OUTPUT CODE FULL-SCALE TRANSITION 111 110 101 011 010 001 000 0 ...
Page 20
Low-Power, 8-Channel, Serial 12-Bit ADCs SUPPLIES +5V - AGND V DGND DD SS MAX186/MAX188 * OPTIONAL Figure 18. Power-Supply Grounding Connection 1 CH0 2 CH1 3 CH2 ANALOG 4 CH3 MAX186 INPUTS 5 CH4 6 CH5 ...
Page 21
... This is a shell program for using a stand-alone 68HC16 without any external memory. The internal 1K RAM * is put into bank $0F to maintain 68HC11 code compatibility. This program was written with software * provided in the Motorola 68HC16 Evaluation Kit Roger J.A. Chen, Applications Engineer * MAXIM Integrated Products * November 20, 1992 * ****************************************************************************************************************************************************** INCLUDE ‘EQUATES.ASM’ ;Equates for common reg addrs INCLUDE ‘ ...
Page 22
Low-Power, 8-Channel, Serial 12-Bit ADCs ;set delay between transfers LDD #$0800 STD SPCR2 ;set ENDQP to $8 for 9 transfers ***** Initialize QSPI Command RAM ***** LDAA #$80 ;CONT=1,BITSE=0,DT=0,DSCK=0,PCS0=ACTIVE STAA $FD40 ;store first byte in COMMAND RAM LDAA #$C0 ;CONT=1,BITSE=1,DT=0,DSCK=0,PCS0=ACTIVE ...
Page 23
Figure 21. QSPI Assembly-Code Timing TMS320C3x to MAX186 Interface Figure 22 shows an application circuit to interface the MAX186/MAX188 to the TMS320 in external clock mode. The timing diagram for this interface circuit is shown in Figure 23. Use the ...
Page 24
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 24 ____________________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 © 1996 Maxim Integrated Products ...