PI3B3257Q Pericom Semiconductor, PI3B3257Q Datasheet - Page 2

• Manufacturer Part Number: PI3B3257Q
• Description: IC QUAD 2-1 BUS SW 16-QSOP
• Manufacturer: Pericom Semiconductor
• Type: Multiplexer/Demultiplexerr

Specifications of PI3B3257Q

• Circuit: 4 x 2:1
• Independent Circuits: 1
• Voltage Supply Source: Single Supply
• Voltage - Supply: 3.3V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-QSOP
• Number Of Bits: 8
• Number Of Elements: 1
• Technology: CMOS
• High Level Output Current: -120mA
• Low Level Output Current: 120mA
• On Resistance: 8Ohm
• Propagation Delay Time: 4.8ns
• Package Type: QSOP
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.97V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.63V
• Quiescent Current: 3uA
• Pin Count: 16
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Current - Output High, Low: -
• Lead Free Status / Rohs Status: Not Compliant

Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Note:
Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not
mplied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
DC Electrical Characteristics
Notes:
1.
2.
3.
Capacitance
Notes:
1.
Storage Temperature ..................................................................... –65°C to +150°C
Ambient Temperature with Power Applied .................................... –40°C to +85°C
Supply Voltage to Ground Potential.................................................–0.5V to +4.6V
DC Input Voltage .............................................................................–0.5V to +4.6V
DC Output Current........................................................................................ 120mA
Power Dissipation ............................................................................................ 0.5W
Parameters
For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
Typical values are at V
Measured by the voltage drop between I and Y pin at indicated current through the switch. On-Resistance is determined by the lower of the
voltages on the two (I,Y) pins.
This parameter is determined by device characterization but is not production tested.
Parameters
I
R
V
V
V
OZH
I
I
IH
ON
IL
IH
IK
C
IL
C
06-0220
OFFYN
C
OFFIN
C
ON
IN
(T
(1)
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
High Impedance Output Current
Clamp Diode Voltage
Switch On-Resistance
A
= 25°C, f = 1 MHz)
Input Capacitance
Y
I
I
CC
N
N
N
/Y
Capacitance, Switch OFF
= 3.3V, T
Capacitance, Switch OFF
Description
N
Capacitance, Switch ON
A
= 25°C ambient and maximum loading.
(Over the Operating Range, T
(3)
Description
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
V
0 ≤ In, Yn ≤ V
V
V
Ion = 48mA or 64mA
V
CC
CC
CC
CC
CC
= Max., V
= Max., V
= Min., I
= Min., V
= Min., V
2
A
IN
= –40°C to +85°C, V
CC
IN
IN
IN
IN
Test Conditions
= –18mA
= 0.0V,
= 2.4V, I
= V
= GND
CC
Test Conditions
V
ON
IN
= 15mA
= 0V
(1)
CC
= 3.3V ±10%)
Mux/DeMux NanoSwitch
Min.
–0.5
2
Typ.
17.0
3.0
8.5
25
Typ.
5
8
(2)
3.3V, Quad 2:1
PS8151K
Max. Units
–1.2
0.8
±1
±1
±1
17
PI3B3257
8
Units
pF
05/16/06
µA
V
V
Ω
™