PI3B3251Q Pericom Semiconductor, PI3B3251Q Datasheet - Page 2

• Manufacturer Part Number: PI3B3251Q
• Description: IC 8-1 MUX/DEMUX BUS SW 16-QSOP
• Manufacturer: Pericom Semiconductor
• Type: Multiplexer/Demultiplexerr

Specifications of PI3B3251Q

• Circuit: 1 x 8:1
• Independent Circuits: 1
• Voltage Supply Source: Single Supply
• Voltage - Supply: 3.3V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-QSOP
• Number Of Bits: 8
• Number Of Elements: 1
• Technology: CMOS
• High Level Output Current: -120mA
• Low Level Output Current: 120mA
• On Resistance: 10Ohm
• Propagation Delay Time: 5.5ns
• Package Type: QSOP
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.97V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.63V
• Quiescent Current: 3uA
• Pin Count: 16
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Current - Output High, Low: -
• Lead Free Status / Rohs Status: Not Compliant

Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Notes:
1.
2.
3.
Capacitance
Note:
1.
DC Electrical Characteristics
Parameters
Storage Temperature ..................................................................... –65°C to +150°C
Ambient Temperature with Power Applied .................................... –40°C to +85°C
Supply Voltage to Ground Potential ................................................–0.5V to +4.6V
DC Input Voltage .............................................................................–0.5V to +4.6V
DC Output Current ........................................................................................ 120mA
Power Dissipation ............................................................................................ 0.5W
For Max. or Min. conditions, use appropriate value specifi ed under Electrical Characteristics for the applicable device type.
Typical values are at V
Measured by the voltage drop between I and Y pin at indicated current through the switch. On-Resistance is determined by the lower of the
voltages on the two (I,Y) pins.
This parameter is determined by device characterization but is not production tested.
Parameters
I
R
V
V
V
OZH
I
I
IH
ON
IL
IH
IK
IL
C
09-0037
C
C
Y(OFF)
I(OFF)
C
I(ON)
IN
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
High Impedance Output Current
Clamp Diode Voltage
Switch On-Resistance
(T
(1)
A
= 25°C, f = 1 MHz)
CC
Input Capacitance
I
Y Capacitance, Switch Off
I
0
0
De scrip tion
- I
- I
= 3.3V, T
7
7
Capacitance, Switch Off
Capacitance, Switch On
A
(3)
= 25°C ambient and maximum loading.
(Over the Operating Range, T
De scrip tion
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
V
0 ≤ I
V
V
I
V
I
ON
ON
CC
CC
CC
CC
CC
= 48mA or 64mA
= 15mA
N
= Max., V
= Max., V
= Min., I
= Min., V
= Min., V
, Y ≤ V
Test Conditions
2
CC
IN
A
IN
IN
IN
IN
= –40°C to +85°C, V
= –18mA
= 0.0V,
= 2.4V,
= V
= GND
CC
(1)
Test Conditions
V
3.3V, 8:1 Mux/DeMux NanoSwitch
IN
Note:
Stresses greater than those listed under MAX I MUM
RATINGS may cause per ma nent dam age to the
device. This is a stress rating only and func tion al
op er a tion of the device at these or any other condi-
tions above those indicated in the operational sec-
tions of this specifi cation is not implied. Ex po sure
to absolute maximum rating conditions for ex tend ed
periods may affect reliability.
= 0V
CC
Min.
–0.5
2.0
=3.3V ±10%)
Typ
10
5
(2)
Typ.
64.0
72.0
3.0
8.0
PS8150G
Max.
–1.2
0.8
±1
±1
±1
17
8
PI3B3251
Units
pF
Units
μA
V
V
Ω
03/02/09
™