PI5C34X245B Pericom Semiconductor, PI5C34X245B Datasheet - Page 2

• Manufacturer Part Number: PI5C34X245B
• Description: IC 32-BIT BUS SWITCH 80-BQSOP
• Manufacturer: Pericom Semiconductor
• Type: Bus Switchr

Specifications of PI5C34X245B

• Circuit: 32 x 1:1
• Independent Circuits: 4
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 80-BQSOP
• Number Of Bits: 32
• Number Of Elements: 4
• Technology: CMOS
• High Level Output Current: -120mA
• Low Level Output Current: 120mA
• On Resistance: 10Ohm
• Propagation Delay Time: 5.6ns
• Package Type: BQSOP
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Quiescent Current: 3uA
• Pin Count: 80
• Mounting: Surface Mount
• Dc: 0433
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Voltage - Supply: -
• Current - Output High, Low: -
• Lead Free Status / Rohs Status: Not Compliant

Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Note:
1.
Notes:
1.
2.
3.
4.
Truth Table
DC Electrical Characteristics
Function
Disconnect
Connect
Parameters
Storage Temperature ..........................................................–65°C to +150°C
Ambient Temperature with Power Applied .........................–40°C to +85°C
Supply Voltage to Ground Potential .....................................–0.5V to +7.0V
DC Input Voltage ..................................................................–0.5V to +7.0V
DC Output Current............................................................................120 mA
Power Dissipation .................................................................................0.5W
H = High Voltage Level
L = Low Voltage Level
Hi-Z = High Impedance
For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
Typical values are at V
Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the
voltages on the two (A,B) pins.
I
R
V
V
V
OZH
I
V
I
I
OS
IH
ON
IL
IH
IK
IL
H
06-0238
(1)
Description
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
High Impedance Output Current
Clamp Diode Voltage
Short Circuit Current
Input Hystersis at Control Pins
Switch On-Resistance
CC
= 5.0V, T
BEn
H
L
A
= 25°C ambient and maximum loading.
(Over the Operating Range, T
(3)
(4)
A0-A31
B0-31
Hi-Z
V
Test Conditions
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
V
0 - A, B - V
V
A (B) = 0V, B (A) = V
V
CC
CC
CC
CC
CC
= Max., V
= Min., V
= Max., V
= Min., I
= Min., V
CC
IN
IN
IN
IN
IN
A
Pin Description
Pin Name
(1)
= –18mA
= –40°C to +85°C, V
= 2.4V, I
= 0V, I
= V
= GND
2
A
B
BE
0
0
CC
CC
-A
-B
X
ON
31
31
ON
= 48mA
Note:
Stresses greater than those listed under MAXIMUM RAT-
INGS may cause permanent damage to the device. This is
a stress rating only and functional operation of the device
at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Ex-
posure to absolute maximum rating conditions for extended
periods may affect reliability.
= 15mA
I/O
I/O
I/O
I
CC
Description
Bus Enable Input (Active LOW)
Bus A
Bus B
= 5V ±10%)
Min.
–0.5
100
2.0
32-Bit, 2-Port Bus Switch
Typ
–0.7
10
5
(2)
PS7058H
Max.
PI5C34X245
–1.2
0.8
±1
±1
±1
15
7
Units
mA
µA
V
V
V
Ω
05/12/06