PI5C32X245B Pericom Semiconductor, PI5C32X245B Datasheet - Page 2

• Manufacturer Part Number: PI5C32X245B
• Description: IC 16-BIT BUS SWITCH 40BQSOP
• Manufacturer: Pericom Semiconductor
• Type: Bus Switchr

Specifications of PI5C32X245B

• Circuit: 8 x 1:1
• Independent Circuits: 2
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 40-BQSOP
• Number Of Bits: 16
• Number Of Elements: 2
• Technology: CMOS
• High Level Output Current: -120mA
• Low Level Output Current: 120mA
• On Resistance: 10Ohm
• Propagation Delay Time: 6.5ns
• Package Type: BQSOP
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Quiescent Current: 3uA
• Pin Count: 40
• Mounting: Surface Mount
• Dc: 05+
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Voltage - Supply: -
• Current - Output High, Low: -
• Lead Free Status / Rohs Status: Not Compliant

Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Notes:
1.
2.
3.
4.
Capacitance
Notes:
1.
DC Electrical Characteristics
C
C
C
V
V
I
I
I
V
I
V
R
Parameters
Storage Temperature ..........................................................–65°C to +150°C
Ambient Temperature with Power Applied .........................–40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) ...–0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) –0.5V to +7.0V
DC Input Voltage ..................................................................–0.5V to +7.0V
DC Output Current ............................................................................120 mA
Power Dissipation .................................................................................0.5W
IH
IL
OZ
OS
IN
OFF
ON
OH
IH
IL
IK
H
Parameters
For Max. or Min. conditions, use appropriate value specifi ed under Electrical Characteristics for the applicable device type.
Typical values are at V
Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined
by the lower of the voltages on the two (A,B) pins.
This parameter is determined by device characterization but is not production tested.
07-0074
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
High Impedance Output Current
Clamp Diode Voltage
S
Input Hysteresis at Control Pins
Switch On-Resistance
(1)
(T
HORT
A
= 25°C, f = 1 MHz)
C
Input Capacitance
A/B Capacitance, Switch Off
A/B Capacitance, Switch On
IRCUIT
CC
De scrip tion
= 5.0V, T
C
URRENT
A
(3)
(4)
(Over the Operating Range, T
= 25°C ambient and maximum loading.
De scrip tion
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
V
0 ≤ A, B ≤ V
V
A (B) = 0V, B (A) = V
V
V
CC
CC
CC
CC
CC
= Max., V
= Max., V
= Min., I
= Min., V
= Min., V
Test Conditions
CC
IN
IN
IN
IN
IN
A
= –18 mA
= 0.0V, I
= 2.4V, I
= V
= GND
= –40°C to +85°C, V
2
CC
CC
ON
ON
(1)
Note:
Stresses greater than those listed under MAX I MUM RAT-
INGS may cause permanent damage to the de vice. This is
a stress rating only and func tion al op er a tion of the device
at these or any other conditions above those indicated in the
operational sections of this specifi cation is not implied. Ex-
posure to absolute max i mum rating conditions for ex tend ed
periods may affect reliability.
= 48 mA
= 15 mA
Test Conditions
V
IN
= 0V
CC
= 5V ±10%)
Min.
–0.5
100
2.0
16-Bit, 2-Port BusSwitch
Typ
–0.7
150
Typ
12
10
6
6
5
(2)
PS7057G
Max.
PI5C32X245
–1.2
0.8
±1
±1
±1
15
7
Units
pF
Units
M
mV
μA
V
V
Ω
03/23/07
A