MAAL-007673-TR1000 MA-COM [M/A-COM Technology Solutions, Inc.], MAAL-007673-TR1000 Datasheet - Page 2

• Manufacturer Part Number: MAAL-007673-TR1000
• Description: Low Noise Amplifier 1.7 - 2.0 GHz
• Manufacturer: MA-COM [M/A-COM Technology Solutions, Inc.]

2
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.
Commitment to produce in volume is not guaranteed.
Low Noise Amplifier
1.7 - 2.0 GHz
Electrical Specifications
Recommended PCB Configuration
MAAL-007673
Component List
6. See plots for 3-volt performance.
R1 (Optional) 35 to 40 Ω
Output 1 dB Compression
Part
C1
L1
Reverse Isolation
Output VSWR
Noise Figure
Bias Current
Input VSWR
Parameter
Input IP3
Gain
500 pF
Value
15 nH
Case Size Manufacturer
0603
0805
0603
6
: T
A
= 25°C, V
1.7 - 2.0 GHz, P
1.7 - 2.0 GHz, P
1.7 - 2.0 GHz, P
1.7 - 2.0 GHz, P
1.7 - 2.0 GHz, P
Panasonic
Coilcraft
Murata
Test Conditions
1.7 - 2.0 GHz
1.7 - 2.0 GHz
DD
—
= +5 V, Z
IN
IN
IN
IN
IN
= -30 dBm
= -30 dBm
= -30 dBm
= -30 dBm
= -30 dBm
M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
changes to the product(s) or information contained herein without notice.
Application Schematic
7.
8.
9.
• North America Tel: [phone] / Fax: [phone]
• Europe Tel: [phone] / Fax: [phone]
• Asia/Pacific Tel: [phone] / Fax: [phone]
Visit www.macomtech.com for additional data sheets and product information.
0
Pins 1, 4, 5 and 8 must be RF and DC grounded as shown.
Pin 3 is the RF input, pin 6 is the RF output. V
applied on pin 7. This pin must be bypassed with a 500 pF
surface mount MLC capacitor, mounted as close as
possible to pin 7, and RF decoupled with a chip inductor
having a minimum value of 15 nH (as shown in the
Recommended PCB Configuration).
Pin 2 allows use of an external resistor to ground for
optional, higher current bias. For nominal current
operation no resistor is used. For optional 20 mA current
operation, connect a 35 to 40 ohm chip resistor (as show in
the Recommended PCB Configuration).
= 50 Ω
RF IN
Units
Ratio
Ratio
dBm
dBm
mA
dB
dB
dB
V
DD
L1
See Note 9
(Optional)
C1
R1
Min.
18
—
—
—
—
—
—
5
7,8,9
Typ.
1.7:1
1.7:1
1.65
20
38
-1
7
8
DD
RF OUT
is
Max.
Rev. V2
2.00
22
11
—
—
—
—
—