HCNW-2201 Agilent(Hewlett-Packard), HCNW-2201 Datasheet - Page 11

• Manufacturer Part Number: HCNW-2201
• Description: Very High CMR/ Wide VCC Logic Gate Optocouplers
• Manufacturer: Agilent(Hewlett-Packard)

Package Characteristics
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable),
your equipment level safety specification or HP Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,”
publication number 5963-2203E.
Notes:
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage
12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together.
1. Each channel.
2. Derate total package power dissipation, P
3. Duration of output short circuit time should not exceed 10 ms.
4. For single devices, input capacitance is measured between pin 2 and pin 3.
5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
6. The t
7. CM
8. For HCPL-2202/12, V
9. Use of a 0.1 F bypass capacitor connected between pins 5 and 8 is recommended.
Withstand
Voltage
Input-Output Momentary
Input-Output Resistance
Input-Output Capacitance
Input-Input Insulation
Leakage Current
Resistance (Input-Input)
Capacitance (Input-Input)
leading edge of the output pulse. The t
pulse to the 1.3 V point on the trailing edge of the output pulse.
V
low state, V
(leakage detection current limit, I
b) shown in the VDE 0884 Insulation Characteristics Table, if applicable.
(leakage detection current limit, I
b) shown in the VDE 0884 Insulation Characteristics Table.
O
> 2.0 V. CM
H
PLH
is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state,
*
Parameter
propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the
O
< 0.8 V.
L
HCNW22XX
HCNW22XX
HCNW22XX
is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic
O
is on pin 6.
I-O
I-O
Sym.
V
R
C
R
C
I
ISO
I-O
I-O
I-I
I-I
I-I
5 A). This test is performed before the 100% production test for partial discharge (Method
5 A). This test is performed before the 100% production test for partial discharge (Method
PHL
T
, linearly above 70 C free-air temperature at a rate of 4.5 mW/ C.
propagation delay is measured from the 50% point on the trailing edge of the input
2500
5000
Min. Typ. Max. Units
10
10
12
11
0.005
10
10
10
0.25
0.6
0.5
12
13
11
0.6
V rms RH < 50%, t = 1 min.
pF
pF
A
T
T
T
T
Relative Humidity = 45%,
t = 5 s, V
V
f = 1 MHz
A
A
A
A
I-I
= 25 C
= 25 C
= 100 C
= 25 C
= 500 V
Test Conditions
I-I
= 500 V
V
f = 1 MHz,
V
I-O
I-O
= 500 Vdc
= 0 Vdc
3000 V rms for one second
6000 V rms for one second
Fig. Note
5, 11
5, 10
1-141
12
12
12
5
5