EDS11-158C FUJI [Fuji Electric], EDS11-158C Datasheet - Page 2

no-image

EDS11-158C

Manufacturer Part Number
EDS11-158C
Description
Manufacturer
FUJI [Fuji Electric]
Datasheet
2
(5) Indication accuracy (at Ta = 23˚C) :
(6) Indication accuracy by change of temperature:
(7) Indication resolution:
(8) Input sampling cycle:
(9) Input impedance:
(10) Variation by signal source resistance:
(11) Allowable wiring resistance:
(12) Allowable input voltage:
(13) Noise rejection ratio:
(14) Input correction:
(15) Overrange, underrange:
2.2 Auxiliary analog input (remote SV input)
(1) Number of inputs:
(2) Input signal: Voltage, 0 to 5 V DC /1 to 5 V DC
(3) Input impedance:
(4) Sampling rate:
2.3 Heater current detector (CT) input
(1) Input type:
(2) Range of detected current:
PXG4
• Thermocouple input:
• Resistance bulb input:
• mV input, voltage input, current input:
(a) User adjustment: Zero point, span
(b) Process value shift:
(c) Input filter: 0.0 to 120.0 sec (filter OFF
Beyond range of -5 to 105% (accuracy
not guaranteed between -5 and 0, and be-
tween 100 and 105%FS)
See Table 1
200 ms
• Thermocouple, mV input: 1 M
• Current input: 250
• Voltage input: About 1 M
• Thermocouple, mV input:
• Voltage input:
• Resistance bulb: 10
• DC voltage input: Between +35 and
• Current input: Within
• Thermocouple, resistance bulb, mV in-
• Normal mode: 40 dB (50/60 Hz)
• Common mode: 120 dB (50/60 Hz)
Up to 1 point
About 1 M
800ms
Single phase CT Up to 1 point
For 1 to 30 A: CTL-6-S-H
For 20 to 50 A: CTL-12-S36-8F
1 to 50A
*except:
Thermocouple B, 0 to 400˚C
Thermocouple R, 0 to 500˚C
Thermocouple T, -200 to 0˚C
digit or
1 digit per 100
500
- 10 V
put: Within
From ground, at 220 V AC, 50/60 Hz
Between input and output, at 220 V AC,
50/60 Hz
0.3%FS/10˚C
1˚C or
0.3%FS
if set at 0.0)
1%FS
0.5%FS 1 digit
5%FS
50%FS for each
0.5˚C, whichever greater
2˚C, whichever greater
1 digit
1 digit
1 digit
5 V
0.3%FS
1˚C
1˚C
1˚C
0.3%FS
MAX. (per wire)
25 mA
10%FS
0.3%FS
1 digit per
0.3%FS
1 digit
MIN.
1
(3) Detected current accuracy:
(4) Detected current resolution:
(5) ON time necessary for detection:
2.4 Digital input (DI)
(1) Number of points:
(2) Specifications: No-voltage contact or transistor input
(3) Contact capacity:
(4) Input judgment:
(5) Sampling pulse width:
(6) Functions:
3.1 Control output
(1) Number of points:
(2) Type:
3. Output section
ized valve control output)
ON assumed at 1 k or lower (contact) or
5 V DC or lower (transistor)
OFF assumed at 100 k
tact) or 18 V DC or higher (transistor)
control standby, AT startup, timer startup,
alarm unlatch, Program selection, start /
stop / reset, PID switching (normal/re-
verse), etc.
Up to 2 points (2 points: Heating/cooling
control)
[1] Relay contact output
[2] SSR/SSC drive output
[3] Current output (0 to 20 mA DC/4 to
[4] Voltage output (0 to 5 V DC/1 to 5 V
Setting
0.1 A
800 ms MIN.
Up to 2 points (up to 3 points for motor-
30 V DC, about 3 mA (per point)
200 ms MIN.
Remote mode selection, SV changeover,
selected out of [1] to [5] below
• Proportional cycle: 1 to 150 sec
• Contact structure: 1 NO (SPST) con-
• Contact capacity:
• Minimum ON/OFF current: 100 mA
• Mechanical life: 20 million operations
• Electrical life: 100,000 operations
• Proportional cycle: 1 to 150 sec
• ON voltage: 20 V DC (18 to 24 V DC)
• OFF voltage: 0.5 V DC or lower
• Maximum current: 20 mA DC (for
• Load resistance: 850
20 mA DC)
• Accuracy:
• Linearity:
• Load resistance: 600
DC/0 to 10 V DC/2 to 10 V DC)
• Accuracy:
• Linearity:
• Load resistance: 10 k
tact
220 V AC/30 V DC, 3 A (resistive
load)
220 V AC/30 V DC, 1 A (inductive
load)
(24 V DC)
MIN. (100 operations/min)
MIN. (rated load)
each of outputs 1 and 2)
10%FS
5%FS
5%FS
5%FS
5%FS
or higher (con-
MIN.
MIN.
MAX.

Related parts for EDS11-158C